Part Number Hot Search : 
4C7V5 WP240 SE040N 1N6623 1210F 2SC6011 SE040N 00410
Product Description
Full Text Search
 

To Download MX29LA128MTTI-90R Datasheet File

  If you can't view the Datasheet, Please click here to try to view without PDF Reader .  
 
 


  Datasheet File OCR Text:
 PRELIMINARY
MX29LA128M T/B
128M-BIT SINGLE VOLTAGE 3V ONLY BOOT SECTOR FLASH MEMORY
FEATURES
GENERAL FEATURES * Single Power Supply Operation - 2.7 to 3.6 volt for read, erase, and program operations * Configuration - 16,777,216 x 8 / 8,388,608 x 16 switchable * Sector structure - 8KB(4KW) x 8 and 64KB(32KW) x 255 * Latch-up protected to 250mA from -1V to VCC + 1V * Low VCC write inhibit is equal to or less than 1.5V * Compatible with JEDEC standard - Pin-out and software compatible to single power supply Flash PERFORMANCE * High Performance - Fast access time: 90R/100ns - Page read time: 25ns - Sector erase time: 0.5s (typ.) - 4 word/8 byte page read buffer - 16 word/ 32 byte write buffer: reduces programming time for multiple-word/byte updates * Low Power Consumption - Active read current: 18mA(typ.) - Active write current: 20mA(typ.) - Standby current: 20uA(typ.) * Minimum 100,000 erase/program cycle * 20-years data retention SOFTWARE FEATURES * Support Common Flash Interface (CFI) - Flash device parameters stored on the device and provide the host system to access. * Program Suspend/Program Resume - Suspend program operation to read other sectors * Erase Suspend/ Erase Resume - Suspends sector erase operation to read data/program other sectors * Status Reply - Data# polling & Toggle bits provide detection of program and erase operation completion HARDWARE FEATURES * Ready/Busy (RY/BY#) Output - Provides a hardware method of detecting program and erase operation completion * Hardware Reset (RESET#) Input - Provides a hardware method to reset the internal state machine to read mode * WP#/ACC input - Write protect (WP#) function allows protection of all sectors, regardless of sector protection settings - ACC (high voltage) accelerates programming time for higher throughput during system SECURITY * Sector Protection/Chip Unprotect - Provides sector group protect function to prevent program or erase operation in the protected sector group - Provides chip unprotect function to allow code changes - Provides temporary sector group unprotect function for code changes in previously protected sector groups * Sector Permanent Lock - A unique lock bit feature allows the content to be permanently locked (Please contact Macronix sales for specific information regarding this permanent lock feature) * Secured Silicon Sector - Provides a 128-word OTP area for permanent, secure identification - Can be programmed and locked at factory or by customer PACKAGE * 56-pin TSOP
GENERAL DESCRIPTION
The MX29LA128M T/B is a 128-mega bit Flash memory organized as 16M bytes of 8 bits or 8M words of 16 bits. MXIC's Flash memories offer the most cost-effective and reliable read/write non-volatile random access memory. The MX29LA128M T/B is packaged in 56-pin TSOP. It is designed to be reprogrammed and erased in system or in standard EPROM programmers.
P/N:PM1170
The standard MX29LA128M T/B offers access time as fast as 90ns, allowing operation of high-speed microprocessors without wait states. To eliminate bus contention, the MX29LA128M T/B has separate chip enable (CE#) and output enable (OE#) controls. MXIC's Flash memories augment EPROM functionality
REV. 0.04, JUL. 11, 2005
1
MX29LA128M T/B
with in-circuit electrical erasure and programming. The MX29LA128M T/B uses a command register to manage this functionality. MXIC Flash technology reliably stores memory contents even after 100,000 erase and program cycles. The MXIC cell is designed to optimize the erase and program mechanisms. In addition, the combination of advanced tunnel oxide processing and low internal electric fields for erase and programming operations produces reliable cycling. The MX29LA128M T/B uses a 2.7V to 3.6V VCC supply to perform the High Reliability Erase and auto Program/Erase algorithms. The highest degree of latch-up protection is achieved with MXIC's proprietary non-epi process. Latch-up protection is proved for stresses up to 100 milliamperes on address and data pin from -1V to VCC + 1V.
AUTOMATIC SECTOR ERASE
The MX29LA128M T/B is sector(s) erasable using MXIC's Auto Sector Erase algorithm. Sector erase modes allow sectors of the array to be erased in one erase cycle. The Automatic Sector Erase algorithm automatically programs the specified sector(s) prior to electrical erase. The timing and verification of electrical erase are controlled internally within the device.
AUTOMATIC ERASE ALGORITHM
MXIC's Automatic Erase algorithm requires the user to write commands to the command register using standard microprocessor write timings. The device will automatically pre-program and verify the entire array. Then the device automatically times the erase pulse width, provides the erase verification, and counts the number of sequences. A status bit toggling between consecutive read cycles provides feedback to the user as to the status of the programming operation. Register contents serve as inputs to an internal statemachine which controls the erase and programming circuitry. During write cycles, the command register internally latches address and data needed for the programming and erase operations. During a system write cycle, addresses are latched on the falling edge, and data are latched on the rising edge of WE# . MXIC's Flash technology combines years of EPROM experience to produce the highest levels of quality, reliability, and cost effectiveness. The MX29LA128M T/B electrically erases all bits simultaneously using FowlerNordheim tunneling. The bytes are programmed by using the EPROM programming mechanism of hot electron injection. During a program cycle, the state-machine will control the program sequences and command register will not respond to any command set. During a Sector Erase cycle, the command register will only respond to Erase Suspend command. After Erase Suspend is completed, the device stays in read mode. After the state machine has completed its task, it will allow the command register to respond to its full command set.
AUTOMATIC PROGRAMMING
The MX29LA128M T/B is byte/word/page programmable using the Automatic Programming algorithm. The Automatic Programming algorithm makes the external system do not need to have time out sequence nor to verify the data programmed.
AUTOMATIC PROGRAMMING ALGORITHM
MXIC's Automatic Programming algorithm require the user to only write program set-up commands (including 2 unlock write cycle and A0H) and a program command (program data and address). The device automatically times the programming pulse width, provides the program verification, and counts the number of sequences. A status bit similar to DATA# polling and a status bit toggling between consecutive read cycles, provide feedback to the user as to the status of the programming operation.
AUTOMATIC CHIP ERASE
The entire chip is bulk erased using 50 ms erase pulses according to MXIC's Automatic Chip Erase algorithm. The Automatic Erase algorithm automatically programs the entire array prior to electrical erase. The timing and verification of electrical erase are controlled internally within the device.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
2
MX29LA128M T/B
PIN CONFIGURATION
56 TSOP
NC A22 A15 A14 A13 A12 A11 A10 A9 A8 A19 A20 WE# RESET# A21 WP#/ACC RY/BY# A18 A17 A7 A6 A5 A4 A3 A2 A1 NC NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 NC NC A16 BYTE# VSS Q15/A-1 Q7 Q14 Q6 Q13 Q5 Q12 Q4 VCC Q11 Q3 Q10 Q2 Q9 Q1 Q8 Q0 OE# VSS CE# A0 NC VIO
PIN DESCRIPTION
SYMBOL A0~A22 Q0~Q14 Q15/A-1 CE# WE# OE# RESET# PIN NAME Address Input Data Inputs/Outputs Q15(Word Mode)/LSB addr(Byte Mode) Chip Enable Input Write Enable Input Output Enable Input Hardware Reset Pin, Active Low Acceleration input RY/BY# BYTE# VCC VI/O GND NC Read/Busy Output Selects 8 bit or 16 bit mode +3.0V single power supply Output Buffer Power (2.7V~3.6V this input should be tied directly to VCC ) Device Ground Pin Not Connected Internally
LOGIC SYMBOL
23 A0-A22 Q0-Q15 (A-1)
16 or 8
CE# OE# WE# RESET# RY/BY# WP#/ACC BYTE# VI/O
WP#/ACC Hardware Write Protect/Programming
P/N:PM1170
REV. 0.04, JUL. 11, 2005
3
MX29LA128M T/B
BLOCK DIAGRAM
CE# OE# WE# WP# BYTE# RESET#
WRITE CONTROL INPUT LOGIC HIGH VOLTAGE MACHINE (WSM) PROGRAM/ERASE STATE
X-DECODER
STATE FLASH ARRAY ARRAY REGISTER
ADDRESS LATCH A0-A22 AND BUFFER
SENSE AMPLIFIER
Y-DECODER
Y-PASS GATE
SOURCE HV COMMAND DATA DECODER
PGM DATA HV COMMAND DATA LATCH
PROGRAM DATA LATCH
Q0-Q15/A-1
I/O BUFFER
P/N:PM1170
REV. 0.04, JUL. 11, 2005
4
MX29LA128M T/B
MX29LA128MT SECTOR ADDRESS TABLE
Sector Group 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 5 5 5 5 6 6 6 6 7 7 7 7 8 8 8 8 9 9 9 9 10 10 10 Sector SA0 SA1 SA2 SA3 SA4 SA5 SA6 SA7 SA8 SA9 SA10 SA11 SA12 SA13 SA14 SA15 SA16 SA17 SA18 SA19 SA20 SA21 SA22 SA23 SA24 SA25 SA26 SA27 SA28 SA29 SA30 SA31 SA32 SA33 SA34 SA35 SA36 SA37 SA38 Sector Address A22-A12 00000000xxx 00000001xxx 00000010xxx 00000011xxx 00000100xxx 00000101xxx 00000110xxx 00000111xxx 00001000xxx 00001001xxx 00001010xxx 00001011xxx 00001100xxx 00001101xxx 00001110xxx 00001111xxx 00010000xxx 00010001xxx 00010010xxx 00010011xxx 00010100xxx 00010101xxx 00010110xxx 00010111xxx 00011000xxx 00011001xxx 00011010xxx 00011011xxx 00011100xxx 00011101xxx 00011110xxx 00011111xxx 00100000xxx 00100001xxx 00100010xxx 00100011xxx 00100100xxx 00100101xxx 00100110xxx Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 (x8) Address Range 000000-0FFFFF 010000-1FFFFF 020000-2FFFFF 030000-3FFFFF 040000-4FFFFF 050000-5FFFFF 060000-6FFFFF 070000-7FFFFF 080000-8FFFFF 090000-9FFFFF 0A0000-AFFFFF 0B0000-BFFFFF 0C0000-CFFFFF 0D0000-DFFFFF 0E0000-EFFFFF 0F0000-FFFFFF 100000-0FFFFF 110000-1FFFFF 120000-2FFFFF 130000-3FFFFF 140000-4FFFFF 150000-5FFFFF 160000-6FFFFF 170000-7FFFFF 180000-8FFFFF 190000-9FFFFF 1A0000-AFFFFF 1B0000-BFFFFF 1C0000-CFFFFF 1D0000-DFFFFF 1E0000-EFFFFF 1F0000-FFFFFF 200000-0FFFFF 210000-1FFFFF 220000-2FFFFF 230000-3FFFFF 240000-4FFFFF 250000-5FFFFF 260000-6FFFFF (x16) Address Range 000000-007FFF 008000-00FFFF 010000-017FFF 018000-01FFFF 020000-027FFF 028000-02FFFF 030000-037FFF 038000-03FFFF 040000-047FFF 048000-04FFFF 050000-057FFF 058000-05FFFF 060000-067FFF 068000-06FFFF 070000-077FFF 078000-07FFFF 080000-087FFF 088000-08FFFF 090000-097FFF 098000-09FFFF 0A0000-0A7FFF 0A8000-0AFFFF 0B0000-0B7FFF 0B8000-0BFFFF 0C0000-0C7FFF 0C8000-0CFFFF 0D0000-0D7FFF 0D8000-0DFFFF 0E0000-0E7FFF 0E8000-0EFFFF 0F0000-0F7FFF 0F8000-0FFFFF 100000-107FFF 108000-10FFFF 110000-117FFF 118000-11FFFF 120000-127FFF 128000-12FFFF 130000-137FFF
P/N:PM1170
REV. 0.04, JUL. 11, 2005
5
MX29LA128M T/B
Sector Group 10 11 11 11 11 12 12 12 12 13 13 13 13 14 14 14 14 15 15 15 15 16 16 16 16 17 17 17 17 18 18 18 18 19 19 19 19 20 20 20 20 Sector SA39 SA40 SA41 SA42 SA43 SA44 SA45 SA46 SA47 SA48 SA49 SA50 SA51 SA52 SA53 SA54 SA55 SA56 SA57 SA58 SA59 SA60 SA61 SA62 SA63 SA64 SA65 SA66 SA67 SA68 SA69 SA70 SA71 SA72 SA73 SA74 SA75 SA76 SA77 SA78 SA79 Sector Address A22-A12 00100111xxx 00101000xxx 00101001xxx 00101010xxx 00101011xxx 00101100xxx 00101101xxx 00101110xxx 00101111xxx 00110000xxx 00110001xxx 00110010xxx 00110011xxx 00110100xxx 00110101xxx 00110110xxx 00110111xxx 00111000xxx 00111001xxx 00111010xxx 00111011xxx 00111100xxx 00111101xxx 00111110xxx 00111111xxx 01000000xxx 01000001xxx 01000010xxx 01000011xxx 01000100xxx 01000101xxx 01000110xxx 01000111xxx 01001000xxx 01001001xxx 01001010xxx 01001011xxx 01001100xxx 01001101xxx 01001110xxx 01001111xxx Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 (x8) Address Range 270000-7FFFFF 280000-8FFFFF 290000-9FFFFF 2A0000-AFFFFF 2B0000-BFFFFF 2C0000-CFFFFF 2D0000-DFFFFF 2E0000-EFFFFF 2F0000-FFFFFF 300000-0FFFFF 310000-1FFFFF 320000-2FFFFF 330000-3FFFFF 340000-4FFFFF 350000-5FFFFF 360000-6FFFFF 370000-7FFFFF 380000-8FFFFF 390000-9FFFFF 3A0000-AFFFFF 3B0000-BFFFFF 3C0000-CFFFFF 3D0000-DFFFFF 3E0000-EFFFFF 3F0000-FFFFFF 400000-0FFFFF 410000-1FFFFF 420000-2FFFFF 430000-3FFFFF 440000-4FFFFF 450000-5FFFFF 460000-6FFFFF 470000-7FFFFF 480000-8FFFFF 490000-9FFFFF 4A0000-AFFFFF 4B0000-BFFFFF 4C0000-CFFFFF 4D0000-DFFFFF 4E0000-EFFFFF 4F0000-FFFFFF (x16) Address Range 138000-13FFFF 140000-147FFF 148000-14FFFF 150000-157FFF 158000-15FFFF 160000-167FFF 168000-16FFFF 170000-177FFF 178000-17FFFF 180000-187FFF 188000-18FFFF 190000-197FFF 198000-19FFFF 1A0000-1A7FFF 1A8000-1AFFFF 1B0000-1B7FFF 1B8000-1BFFFF 1C0000-1C7FFF 1C8000-1CFFFF 1D0000-1D7FFF 1D8000-1DFFFF 1E0000-1E7FFF 1E8000-1EFFFF 1F0000-1F7FFF 1F8000-1FFFFF 200000-207FFF 208000-20FFFF 210000-217FFF 218000-21FFFF 220000-227FFF 228000-22FFFF 230000-237FFF 238000-23FFFF 240000-247FFF 248000-24FFFF 250000-257FFF 258000-25FFFF 260000-267FFF 268000-26FFFF 270000-277FFF 278000-27FFFF
P/N:PM1170
REV. 0.04, JUL. 11, 2005
6
MX29LA128M T/B
Sector Group 21 21 21 21 22 22 22 22 23 23 23 23 24 24 24 24 25 25 25 25 26 26 26 26 27 27 27 27 28 28 28 28 29 29 29 29 30 30 30 30 31 Sector SA80 SA81 SA82 SA83 SA84 SA85 SA86 SA87 SA88 SA89 SA90 SA91 SA92 SA93 SA94 SA95 SA96 SA97 SA98 SA99 SA100 SA101 SA102 SA103 SA104 SA105 SA106 SA107 SA108 SA109 SA110 SA111 SA112 SA113 SA114 SA115 SA116 SA117 SA118 SA119 SA120 Sector Address A22-A12 01010000xxx 01010001xxx 01010010xxx 01010011xxx 01010100xxx 01010101xxx 01010110xxx 01010111xxx 01011000xxx 01011001xxx 01011010xxx 01011011xxx 01011100xxx 01011101xxx 01011110xxx 01011111xxx 01100000xxx 01100001xxx 01100010xxx 01100011xxx 01100100xxx 01100101xxx 01100110xxx 01100111xxx 01101000xxx 01101001xxx 01101010xxx 01101011xxx 01101100xxx 01101101xxx 01101110xxx 01101111xxx 01110000xxx 01110001xxx 01110010xxx 01110011xxx 01110100xxx 01110101xxx 01110110xxx 01110111xxx 01111000xxx Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 (x8) Address Range 500000-0FFFFF 510000-1FFFFF 520000-2FFFFF 530000-3FFFFF 540000-4FFFFF 550000-5FFFFF 560000-6FFFFF 570000-7FFFFF 580000-8FFFFF 590000-9FFFFF 5A0000-AFFFFF 5B0000-BFFFFF 5C0000-CFFFFF 5D0000-DFFFFF 5E0000-EFFFFF 5F0000-FFFFFF 600000-0FFFFF 610000-1FFFFF 620000-2FFFFF 630000-3FFFFF 640000-4FFFFF 650000-5FFFFF 660000-6FFFFF 670000-7FFFFF 680000-8FFFFF 690000-9FFFFF 6A0000-AFFFFF 6B0000-BFFFFF 6C0000-CFFFFF 6D0000-DFFFFF 6E0000-EFFFFF 6F0000-FFFFFF 700000-0FFFFF 710000-1FFFFF 720000-2FFFFF 730000-3FFFFF 740000-4FFFFF 750000-5FFFFF 760000-6FFFFF 770000-7FFFFF 780000-8FFFFF (x16) Address Range 280000-287FFF 288000-28FFFF 290000-297FFF 298000-29FFFF 2A0000-2A7FFF 2A8000-2AFFFF 2B0000-2B7FFF 2B8000-2BFFFF 2C0000-2C7FFF 2C8000-2CFFFF 2D0000-2D7FFF 2D8000-2DFFFF 2E0000-2E7FFF 2E8000-2EFFFF 2F0000-2F7FFF 2F8000-2FFFFF 300000-307FFF 308000-30FFFF 310000-317FFF 318000-31FFFF 320000-327FFF 328000-32FFFF 330000-337FFF 338000-33FFFF 340000-347FFF 348000-34FFFF 350000-357FFF 358000-35FFFF 360000-367FFF 368000-36FFFF 370000-377FFF 378000-37FFFF 380000-387FFF 388000-38FFFF 390000-397FFF 398000-39FFFF 3A0000-3A7FFF 3A8000-3AFFFF 3B0000-3B7FFF 3B8000-3BFFFF 3C0000-3C7FFF
P/N:PM1170
REV. 0.04, JUL. 11, 2005
7
MX29LA128M T/B
Sector Group 31 31 31 32 32 32 32 33 33 33 33 34 34 34 34 35 35 35 35 36 36 36 36 37 37 37 37 38 38 38 38 39 39 39 39 40 40 40 40 41 41 Sector SA121 SA122 SA123 SA124 SA125 SA126 SA127 SA128 SA129 SA130 SA131 SA132 SA133 SA134 SA135 SA136 SA137 SA138 SA139 SA140 SA141 SA142 SA143 SA144 SA145 SA146 SA147 SA148 SA149 SA150 SA151 SA152 SA153 SA154 SA155 SA156 SA157 SA158 SA159 SA160 SA161 Sector Address A22-A12 01111001xxx 01111010xxx 01111011xxx 01111100xxx 01111101xxx 01111110xxx 01111111xxx 10000000xxx 10000001xxx 10000010xxx 10000011xxx 10000100xxx 10000101xxx 10000110xxx 10000111xxx 10001000xxx 10001001xxx 10001010xxx 10001011xxx 10001100xxx 10001101xxx 10001110xxx 10001111xxx 10010000xxx 10010001xxx 10010010xxx 10010011xxx 10010100xxx 10010101xxx 10010110xxx 10010111xxx 10011000xxx 10011001xxx 10011010xxx 10011011xxx 10011100xxx 10011101xxx 10011110xxx 10011111xxx 10100000xxx 10100001xxx Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 (x8) Address Range 790000-9FFFFF 7A0000-AFFFFF 7B0000-BFFFFF 7C0000-CFFFFF 7D0000-DFFFFF 7E0000-EFFFFF 7F0000-FFFFFF 800000-0FFFFF 810000-1FFFFF 820000-2FFFFF 830000-3FFFFF 840000-4FFFFF 850000-5FFFFF 860000-6FFFFF 870000-7FFFFF 880000-8FFFFF 890000-9FFFFF 8A0000-AFFFFF 8B0000-BFFFFF 8C0000-CFFFFF 8D0000-DFFFFF 8E0000-EFFFFF 8F0000-FFFFFF 900000-0FFFFF 910000-1FFFFF 920000-2FFFFF 930000-3FFFFF 940000-4FFFFF 950000-5FFFFF 960000-6FFFFF 970000-7FFFFF 980000-8FFFFF 990000-9FFFFF 9A0000-AFFFFF 9B0000-BFFFFF 9C0000-CFFFFF 9D0000-DFFFFF 9E0000-EFFFFF 9F0000-FFFFFF A00000-0FFFFF A10000-1FFFFF (x16) Address Range 3C8000-3CFFFF 3D0000-3D7FFF 3D8000-3DFFFF 3E0000-3E7FFF 3E8000-3EFFFF 3F0000-3F7FFF 3F8000-3FFFFF 400000-407FFF 408000-40FFFF 410000-417FFF 418000-41FFFF 420000-427FFF 428000-42FFFF 430000-437FFF 438000-43FFFF 440000-447FFF 448000-44FFFF 450000-457FFF 458000-45FFFF 460000-467FFF 468000-46FFFF 470000-477FFF 478000-47FFFF 480000-487FFF 488000-48FFFF 490000-497FFF 498000-49FFFF 4A0000-4A7FFF 4A8000-4AFFFF 4B0000-4B7FFF 4B8000-4BFFFF 4C0000-4C7FFF 4C8000-4CFFFF 4D0000-4D7FFF 4D8000-4DFFFF 4E0000-4E7FFF 4E8000-4EFFFF 4F0000-4F7FFF 4F8000-4FFFFF 500000-507FFF 508000-50FFFF
P/N:PM1170
REV. 0.04, JUL. 11, 2005
8
MX29LA128M T/B
Sector Group 41 41 42 42 42 42 43 43 43 43 44 44 44 44 45 45 45 45 46 46 46 46 47 47 47 47 48 48 48 48 49 49 49 49 50 50 50 50 51 51 51 Sector SA162 SA163 SA164 SA165 SA166 SA167 SA168 SA169 SA170 SA171 SA172 SA173 SA174 SA175 SA176 SA177 SA178 SA179 SA180 SA181 SA182 SA183 SA184 SA185 SA186 SA187 SA188 SA189 SA190 SA191 SA192 SA193 SA194 SA195 SA196 SA197 SA198 SA199 SA200 SA201 SA202 Sector Address A22-A12 10100010xxx 10100011xxx 10100100xxx 10100101xxx 10100110xxx 10100111xxx 10101000xxx 10101001xxx 10101010xxx 10101011xxx 10101100xxx 10101101xxx 10101110xxx 10101111xxx 10110000xxx 10110001xxx 10110010xxx 10110011xxx 10110100xxx 10110101xxx 10110110xxx 10110111xxx 10111000xxx 10111001xxx 10111010xxx 10111011xxx 10111100xxx 10111101xxx 10111110xxx 10111111xxx 11000000xxx 11000001xxx 11000010xxx 11000011xxx 11000100xxx 11000101xxx 11000110xxx 11000111xxx 11001000xxx 11001001xxx 11001010xxx Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 (x8) Address Range A20000-2FFFFF A30000-3FFFFF A40000-4FFFFF A50000-5FFFFF A60000-6FFFFF A70000-7FFFFF A80000-8FFFFF A90000-9FFFFF AA0000-AFFFFF AB0000-BFFFFF AC0000-CFFFFF AD0000-DFFFFF AE0000-EFFFFF AF0000-FFFFFF B00000-0FFFFF B10000-1FFFFF B20000-2FFFFF B30000-3FFFFF B40000-4FFFFF B50000-5FFFFF B60000-6FFFFF B70000-7FFFFF B80000-8FFFFF B90000-9FFFFF BA0000-AFFFFF BB0000-BFFFFF BC0000-CFFFFF BD0000-DFFFFF BE0000-EFFFFF BF0000-FFFFFF C00000-0FFFFF C10000-1FFFFF C20000-2FFFFF C30000-3FFFFF C40000-4FFFFF C50000-5FFFFF C60000-6FFFFF C70000-7FFFFF C80000-8FFFFF C90000-9FFFFF CA0000-AFFFFF (x16) Address Range 510000-517FFF 518000-51FFFF 520000-527FFF 528000-52FFFF 530000-537FFF 538000-53FFFF 540000-547FFF 548000-54FFFF 550000-557FFF 558000-55FFFF 560000-567FFF 568000-56FFFF 570000-577FFF 578000-57FFFF 580000-587FFF 588000-58FFFF 590000-597FFF 598000-59FFFF 5A0000-5A7FFF 5A8000-5AFFFF 5B0000-5B7FFF 5B8000-5BFFFF 5C0000-5C7FFF 5C8000-5CFFFF 5D0000-5D7FFF 5D8000-5DFFFF 5E0000-5E7FFF 5E8000-5EFFFF 5F0000-5F7FFF 5F8000-5FFFFF 600000-607FFF 608000-60FFFF 610000-617FFF 618000-61FFFF 620000-627FFF 628000-62FFFF 630000-637FFF 638000-63FFFF 640000-647FFF 648000-64FFFF 650000-657FFF
P/N:PM1170
REV. 0.04, JUL. 11, 2005
9
MX29LA128M T/B
Sector Group 51 52 52 52 52 53 53 53 53 54 54 54 54 55 55 55 55 56 56 56 56 57 57 57 57 58 58 58 58 59 59 59 59 60 60 60 60 61 Sector SA203 SA204 SA205 SA206 SA207 SA208 SA209 SA210 SA211 SA212 SA213 SA214 SA215 SA216 SA217 SA218 SA219 SA220 SA221 SA222 SA223 SA224 SA225 SA226 SA227 SA228 SA229 SA230 SA231 SA232 SA233 SA234 SA235 SA236 SA237 SA238 SA239 SA240 Sector Address A22-A12 11001011xxx 11001100xxx 11001101xxx 11001110xxx 11001111xxx 11010000xxx 11010001xxx 11010010xxx 11010011xxx 11010100xxx 11010101xxx 11010110xxx 11010111xxx 11011000xxx 11011001xxx 11011010xxx 11011011xxx 11011100xxx 11011101xxx 11011110xxx 11011111xxx 11100000xxx 11100001xxx 11100010xxx 11100011xxx 11100100xxx 11100101xxx 11100110xxx 11100111xxx 11101000xxx 11101001xxx 11101010xxx 11101011xxx 11101100xxx 11101101xxx 11101110xxx 11101111xxx 11110000xxx Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 (x8) Address Range CB0000-BFFFFF CC0000-CFFFFF CD0000-DFFFFF CE0000-EFFFFF CF0000-FFFFFF D00000-0FFFFF D10000-1FFFFF D20000-2FFFFF D30000-3FFFFF D40000-4FFFFF D50000-5FFFFF D60000-6FFFFF D70000-7FFFFF D80000-8FFFFF D90000-9FFFFF DA0000-AFFFFF DB0000-BFFFFF DC0000-CFFFFF DD0000-DFFFFF DE0000-EFFFFF DF0000-FFFFFF E00000-0FFFFF E10000-1FFFFF E20000-2FFFFF E30000-3FFFFF E40000-4FFFFF E50000-5FFFFF E60000-6FFFFF E70000-7FFFFF E80000-8FFFFF E90000-9FFFFF EA0000-AFFFFF EB0000-BFFFFF EC0000-CFFFFF ED0000-DFFFFF EE0000-EFFFFF EF0000-FFFFFF F00000-0FFFFFF (x16) Address Range 658000-65FFFF 660000-667FFF 668000-66FFFF 670000-677FFF 678000-67FFFF 680000-687FFF 688000-68FFFF 690000-697FFF 698000-69FFFF 6A0000-6A7FFF 6A8000-6AFFFF 6B0000-6B7FFF 6B8000-6BFFFF 6C0000-6C7FFF 6C8000-6CFFFF 6D0000-6D7FFF 6D8000-6DFFFF 6E0000-6E7FFF 6E8000-6EFFFF 6F0000-6F7FFF 6F8000-6FFFFF 700000-707FFF 708000-70FFFF 710000-717FFF 718000-71FFFF 720000-727FFF 728000-72FFFF 730000-737FFF 738000-73FFFF 740000-747FFF 748000-74FFFF 750000-757FFF 758000-75FFFF 760000-767FFF 768000-76FFFF 770000-777FFF 778000-77FFFF 780000-787FFF
P/N:PM1170
REV. 0.04, JUL. 11, 2005
10
MX29LA128M T/B
Sector Group 61 61 61 62 62 62 62 63 63 63 63 64 64 64 65 66 67 68 69 70 71 72 Sector SA241 SA242 SA243 SA244 SA245 SA246 SA247 SA248 SA249 SA250 SA251 SA252 SA253 SA254 SA255 SA256 SA257 SA258 SA259 SA260 SA261 SA262 Sector Address A22-A12 11110001xxx 11110010xxx 11110011xxx 11110100xxx 11110101xxx 11110110xxx 11110111xxx 11111000xxx 11111001xxx 11111010xxx 11111011xxx 11111100xxx 11111101xxx 11111110xxx 11111111000 11111111001 11111111010 11111111011 11111111100 11111111101 11111111110 11111111111 Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 8/4 8/4 8/4 8/4 8/4 8/4 8/4 8/4 (x8) Address Range F10000-1FFFFF F20000-2FFFFF F30000-3FFFFF F40000-4FFFFF F50000-5FFFFF F60000-6FFFFF F70000-7FFFFF F80000-8FFFFF F90000-9FFFFF FA0000-AFFFFF FB0000-BFFFFF FC0000-CFFFFF FD0000-DFFFFF FE0000-EFFFFF FF0000-FF1FFF FF2000-FF3FFF FF4000-FF5FFF FF6000-FF7FFF FF8000-FF9FFF FFA000-FFBFFF FFC000-FFDFFF FFE000-FFFFFF (x16) Address Range 788000-78FFFF 790000-797FFF 798000-79FFFF 7A0000-7A7FFF 7A8000-7AFFFF 7B0000-7B7FFF 7B8000-7BFFFF 7C0000-7C7FFF 7C8000-7CFFFF 7D0000-7D7FFF 7D8000-7DFFFF 7E0000-7E7FFF 7E8000-7EFFFF 7F0000-7F7FFF 7F8000-7F8FFF 7F9000-7F9FFF 7FA000-7FAFFF 7FB000-7FBFFF 7FC000-7FCFFF 7FD000-7FDFFF 7FE000-7FEFFF 7FF000-7FFFFF
P/N:PM1170
REV. 0.04, JUL. 11, 2005
11
MX29LA128M T/B
MX29LA128MB SECTOR ADDRESS TABLE
Sector Group 1 2 3 4 5 6 7 8 9 9 9 10 10 10 10 11 11 11 11 12 12 12 12 13 13 13 13 14 14 14 14 15 15 15 15 16 16 16 16 Sector SA0 SA1 SA2 SA3 SA4 SA5 SA6 SA7 SA8 SA9 SA10 SA11 SA12 SA13 SA14 SA15 SA16 SA17 SA18 SA19 SA20 SA21 SA22 SA23 SA24 SA25 SA26 SA27 SA28 SA29 SA30 SA31 SA32 SA33 SA34 SA35 SA36 SA37 SA38 Sector Address A22-A12 00000000000 00000000001 00000000010 00000000011 00000000100 00000000101 00000000110 00000000111 00000001xxx 00000010xxx 00000011xxx 00000100xxx 00000101xxx 00000110xxx 00000111xxx 00001000xxx 00001001xxx 00001010xxx 00001011xxx 00001100xxx 00001101xxx 00001110xxx 00001111xxx 00010000xxx 00010001xxx 00010010xxx 00010011xxx 00010100xxx 00010101xxx 00010110xxx 00010111xxx 00011000xxx 00011001xxx 00011010xxx 00011011xxx 00011100xxx 00011101xxx 00011110xxx 00011111xxx Sector Size (Kbytes/Kwords) 8/4 8/4 8/4 8/4 8/4 8/4 8/4 8/4 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 (x8) Address Range 000000-001FFF 002000-003FFF 004000-005FFF 006000-007FFF 008000-009FFF 00A000-00BFFF 00C000-00DFFF 00E000-00FFFF 010000-1FFFFF 020000-2FFFFF 030000-3FFFFF 040000-4FFFFF 050000-5FFFFF 060000-6FFFFF 070000-7FFFFF 080000-8FFFFF 090000-9FFFFF 0A0000-AFFFFF 0B0000-BFFFFF 0C0000-CFFFFF 0D0000-DFFFFF 0E0000-EFFFFF 0F0000-FFFFFF 100000-0FFFFF 110000-1FFFFF 120000-2FFFFF 130000-3FFFFF 140000-4FFFFF 150000-5FFFFF 160000-6FFFFF 170000-7FFFFF 180000-8FFFFF 190000-9FFFFF 1A0000-AFFFFF 1B0000-BFFFFF 1C0000-CFFFFF 1D0000-DFFFFF 1E0000-EFFFFF 1F0000-FFFFFF (x16) Address Range 000000-000FFF 001000-001FFF 002000-002FFF 003000-003FFF 004000-004FFF 005000-005FFF 006000-006FFF 007000-007FFF 008000-00FFFF 010000-017FFF 018000-01FFFF 020000-027FFF 028000-02FFFF 030000-037FFF 038000-03FFFF 040000-047FFF 048000-04FFFF 050000-057FFF 058000-05FFFF 060000-067FFF 068000-06FFFF 070000-077FFF 078000-07FFFF 080000-087FFF 088000-08FFFF 090000-097FFF 098000-09FFFF 0A0000-0A7FFF 0A8000-0AFFFF 0B0000-0B7FFF 0B8000-0BFFFF 0C0000-0C7FFF 0C8000-0CFFFF 0D0000-0D7FFF 0D8000-0DFFFF 0E0000-0E7FFF 0E8000-0EFFFF 0F0000-0F7FFF 0F8000-0FFFFF
P/N:PM1170
REV. 0.04, JUL. 11, 2005
12
MX29LA128M T/B
Sector Group 17 17 17 17 18 18 18 18 19 19 19 19 20 20 20 20 21 21 21 21 22 22 22 22 23 23 23 23 24 24 24 24 25 25 25 25 26 26 26 26 27 Sector SA39 SA40 SA41 SA42 SA43 SA44 SA45 SA46 SA47 SA48 SA49 SA50 SA51 SA52 SA53 SA54 SA55 SA56 SA57 SA58 SA59 SA60 SA61 SA62 SA63 SA64 SA65 SA66 SA67 SA68 SA69 SA70 SA71 SA72 SA73 SA74 SA75 SA76 SA77 SA78 SA79 Sector Address A22-A12 00100000xxx 00100001xxx 00100010xxx 00100011xxx 00100100xxx 00100101xxx 00100110xxx 00100111xxx 00101000xxx 00101001xxx 00101010xxx 00101011xxx 00101100xxx 00101101xxx 00101110xxx 00101111xxx 00110000xxx 00110001xxx 00110010xxx 00110011xxx 00110100xxx 00110101xxx 00110110xxx 00110111xxx 00111000xxx 00111001xxx 00111010xxx 00111011xxx 00111100xxx 00111101xxx 00111110xxx 00111111xxx 01000000xxx 01000001xxx 01000010xxx 01000011xxx 01000100xxx 01000101xxx 01000110xxx 01000111xxx 01001000xxx Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 (x8) Address Range 200000-0FFFFF 210000-1FFFFF 220000-2FFFFF 230000-3FFFFF 240000-4FFFFF 250000-5FFFFF 260000-6FFFFF 270000-7FFFFF 280000-8FFFFF 290000-9FFFFF 2A0000-AFFFFF 2B0000-BFFFFF 2C0000-CFFFFF 2D0000-DFFFFF 2E0000-EFFFFF 2F0000-FFFFFF 300000-0FFFFF 310000-1FFFFF 320000-2FFFFF 330000-3FFFFF 340000-4FFFFF 350000-5FFFFF 360000-6FFFFF 370000-7FFFFF 380000-8FFFFF 390000-9FFFFF 3A0000-AFFFFF 3B0000-BFFFFF 3C0000-CFFFFF 3D0000-DFFFFF 3E0000-EFFFFF 3F0000-FFFFFF 400000-0FFFFF 410000-1FFFFF 420000-2FFFFF 430000-3FFFFF 440000-4FFFFF 450000-5FFFFF 460000-6FFFFF 470000-7FFFFF 480000-8FFFFF (x16) Address Range 100000-107FFF 108000-10FFFF 110000-117FFF 118000-11FFFF 120000-127FFF 128000-12FFFF 130000-137FFF 138000-13FFFF 140000-147FFF 148000-14FFFF 150000-157FFF 158000-15FFFF 160000-167FFF 168000-16FFFF 170000-177FFF 178000-17FFFF 180000-187FFF 188000-18FFFF 190000-197FFF 198000-19FFFF 1A0000-1A7FFF 1A8000-1AFFFF 1B0000-1B7FFF 1B8000-1BFFFF 1C0000-1C7FFF 1C8000-1CFFFF 1D0000-1D7FFF 1D8000-1DFFFF 1E0000-1E7FFF 1E8000-1EFFFF 1F0000-1F7FFF 1F8000-1FFFFF 200000-207FFF 208000-20FFFF 210000-217FFF 218000-21FFFF 220000-227FFF 228000-22FFFF 230000-237FFF 238000-23FFFF 240000-247FFF
P/N:PM1170
REV. 0.04, JUL. 11, 2005
13
MX29LA128M T/B
Sector Group 27 27 27 28 28 28 28 29 29 29 29 30 30 30 30 31 31 31 31 32 32 32 32 33 33 33 33 34 34 34 34 35 35 35 35 36 36 36 36 37 37 Sector SA80 SA81 SA82 SA83 SA84 SA85 SA86 SA87 SA88 SA89 SA90 SA91 SA92 SA93 SA94 SA95 SA96 SA97 SA98 SA99 SA100 SA101 SA102 SA103 SA104 SA105 SA106 SA107 SA108 SA109 SA110 SA111 SA112 SA113 SA114 SA115 SA116 SA117 SA118 SA119 SA120 Sector Address A22-A12 01001001xxx 01001010xxx 01001011xxx 01001100xxx 01001101xxx 01001110xxx 01001111xxx 01010000xxx 01010001xxx 01010010xxx 01010011xxx 01010100xxx 01010101xxx 01010110xxx 01010111xxx 01011000xxx 01011001xxx 01011010xxx 01011011xxx 01011100xxx 01011101xxx 01011110xxx 01011111xxx 01100000xxx 01100001xxx 01100010xxx 01100011xxx 01100100xxx 01100101xxx 01100110xxx 01100111xxx 01101000xxx 01101001xxx 01101010xxx 01101011xxx 01101100xxx 01101101xxx 01101110xxx 01101111xxx 01110000xxx 01110001xxx Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 (x8) Address Range 490000-9FFFFF 4A0000-AFFFFF 4B0000-BFFFFF 4C0000-CFFFFF 4D0000-DFFFFF 4E0000-EFFFFF 4F0000-FFFFFF 500000-0FFFFF 510000-1FFFFF 520000-2FFFFF 530000-3FFFFF 540000-4FFFFF 550000-5FFFFF 560000-6FFFFF 570000-7FFFFF 580000-8FFFFF 590000-9FFFFF 5A0000-AFFFFF 5B0000-BFFFFF 5C0000-CFFFFF 5D0000-DFFFFF 5E0000-EFFFFF 5F0000-FFFFFF 600000-0FFFFF 610000-1FFFFF 620000-2FFFFF 630000-3FFFFF 640000-4FFFFF 650000-5FFFFF 660000-6FFFFF 670000-7FFFFF 680000-8FFFFF 690000-9FFFFF 6A0000-AFFFFF 6B0000-BFFFFF 6C0000-CFFFFF 6D0000-DFFFFF 6E0000-EFFFFF 6F0000-FFFFFF 700000-0FFFFF 710000-1FFFFF (x16) Address Range 248000-24FFFF 250000-257FFF 258000-25FFFF 260000-267FFF 268000-26FFFF 270000-277FFF 278000-27FFFF 280000-287FFF 288000-28FFFF 290000-297FFF 298000-29FFFF 2A0000-2A7FFF 2A8000-2AFFFF 2B0000-2B7FFF 2B8000-2BFFFF 2C0000-2C7FFF 2C8000-2CFFFF 2D0000-2D7FFF 2D8000-2DFFFF 2E0000-2E7FFF 2E8000-2EFFFF 2F0000-2F7FFF 2F8000-2FFFFF 300000-307FFF 308000-30FFFF 310000-317FFF 318000-31FFFF 320000-327FFF 328000-32FFFF 330000-337FFF 338000-33FFFF 340000-347FFF 348000-34FFFF 350000-357FFF 358000-35FFFF 360000-367FFF 368000-36FFFF 370000-377FFF 378000-37FFFF 380000-387FFF 388000-38FFFF
P/N:PM1170
REV. 0.04, JUL. 11, 2005
14
MX29LA128M T/B
Sector Group 37 37 38 38 38 38 39 39 39 39 40 40 40 40 41 41 41 41 42 42 42 42 43 43 43 43 44 44 44 44 45 45 45 45 46 46 46 46 47 47 47 47
P/N:PM1170
Sector SA121 SA122 SA123 SA124 SA125 SA126 SA127 SA128 SA129 SA130 SA131 SA132 SA133 SA134 SA135 SA136 SA137 SA138 SA139 SA140 SA141 SA142 SA143 SA144 SA145 SA146 SA147 SA148 SA149 SA150 SA151 SA152 SA153 SA154 SA155 SA156 SA157 SA158 SA159 SA160 SA161 SA162
Sector Address A22-A12 01110010xxx 01110011xxx 01110100xxx 01110101xxx 01110110xxx 01110111xxx 01111000xxx 01111001xxx 01111010xxx 01111011xxx 01111100xxx 01111101xxx 01111110xxx 01111111xxx 10000000xxx 10000001xxx 10000010xxx 10000011xxx 10000100xxx 10000101xxx 10000110xxx 10000111xxx 10001000xxx 10001001xxx 10001010xxx 10001011xxx 10001100xxx 10001101xxx 10001110xxx 10001111xxx 10010000xxx 10010001xxx 10010010xxx 10010011xxx 10010100xxx 10010101xxx 10010110xxx 10010111xxx 10011000xxx 10011001xxx 10011010xxx 10011011xxx
Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32
(x8) Address Range 720000-2FFFFF 730000-3FFFFF 740000-4FFFFF 750000-5FFFFF 760000-6FFFFF 770000-7FFFFF 780000-8FFFFF 790000-9FFFFF 7A0000-AFFFFF 7B0000-BFFFFF 7C0000-CFFFFF 7D0000-DFFFFF 7E0000-EFFFFF 7F0000-FFFFFF 800000-0FFFFF 810000-1FFFFF 820000-2FFFFF 830000-3FFFFF 840000-4FFFFF 850000-5FFFFF 860000-6FFFFF 870000-7FFFFF 880000-8FFFFF 890000-9FFFFF 8A0000-AFFFFF 8B0000-BFFFFF 8C0000-CFFFFF 8D0000-DFFFFF 8E0000-EFFFFF 8F0000-FFFFFF 900000-0FFFFF 910000-1FFFFF 920000-2FFFFF 930000-3FFFFF 940000-4FFFFF 950000-5FFFFF 960000-6FFFFF 970000-7FFFFF 980000-8FFFFF 990000-9FFFFF 9A0000-AFFFFF 9B0000-BFFFFF
(x16) Address Range 390000-397FFF 398000-39FFFF 3A0000-3A7FFF 3A8000-3AFFFF 3B0000-3B7FFF 3B8000-3BFFFF 3C0000-3C7FFF 3C8000-3CFFFF 3D0000-3D7FFF 3D8000-3DFFFF 3E0000-3E7FFF 3E8000-3EFFFF 3F0000-3F7FFF 3F8000-3FFFFF 400000-407FFF 408000-40FFFF 410000-417FFF 418000-41FFFF 420000-427FFF 428000-42FFFF 430000-437FFF 438000-43FFFF 440000-447FFF 448000-44FFFF 450000-457FFF 458000-45FFFF 460000-467FFF 468000-46FFFF 470000-477FFF 478000-47FFFF 480000-487FFF 488000-48FFFF 490000-497FFF 498000-49FFFF 4A0000-4A7FFF 4A8000-4AFFFF 4B0000-4B7FFF 4B8000-4BFFFF 4C0000-4C7FFF 4C8000-4CFFFF 4D0000-4D7FFF 4D8000-4DFFFF
REV. 0.04, JUL. 11, 2005
15
MX29LA128M T/B
Sector Group 48 48 48 48 49 49 49 49 50 50 50 50 51 51 51 51 52 52 52 52 53 53 53 53 54 54 54 54 55 55 55 55 56 56 56 56 57 57 57 57 Sector SA163 SA164 SA165 SA166 SA167 SA168 SA169 SA170 SA171 SA172 SA173 SA174 SA175 SA176 SA177 SA178 SA179 SA180 SA181 SA182 SA183 SA184 SA185 SA186 SA187 SA188 SA189 SA190 SA191 SA192 SA193 SA194 SA195 SA196 SA197 SA198 SA199 SA200 SA201 SA202 Sector Address A22-A12 10011100xxx 10011101xxx 10011110xxx 10011111xxx 10100000xxx 10100001xxx 10100010xxx 10100011xxx 10100100xxx 10100101xxx 10100110xxx 10100111xxx 10101000xxx 10101001xxx 10101010xxx 10101011xxx 10101100xxx 10101101xxx 10101110xxx 10101111xxx 10110000xxx 10110001xxx 10110010xxx 10110011xxx 10110100xxx 10110101xxx 10110110xxx 10110111xxx 10111000xxx 10111001xxx 10111010xxx 10111011xxx 10111100xxx 10111101xxx 10111110xxx 10111111xxx 11000000xxx 11000001xxx 11000010xxx 11000011xxx Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 (x8) Address Range 9C0000-CFFFFF 9D0000-DFFFFF 9E0000-EFFFFF 9F0000-FFFFFF A00000-0FFFFF A10000-1FFFFF A20000-2FFFFF A30000-3FFFFF A40000-4FFFFF A50000-5FFFFF A60000-6FFFFF A70000-7FFFFF A80000-8FFFFF A90000-9FFFFF AA0000-AFFFFF AB0000-BFFFFF AC0000-CFFFFF AD0000-DFFFFF AE0000-EFFFFF AF0000-FFFFFF B00000-0FFFFF B10000-1FFFFF B20000-2FFFFF B30000-3FFFFF B40000-4FFFFF B50000-5FFFFF B60000-6FFFFF B70000-7FFFFF B80000-8FFFFF B90000-9FFFFF BA0000-AFFFFF BB0000-BFFFFF BC0000-CFFFFF BD0000-DFFFFF BE0000-EFFFFF BF0000-FFFFFF C00000-0FFFFF C10000-1FFFFF C20000-2FFFFF C30000-3FFFFF (x16) Address Range 4E0000-4E7FFF 4E8000-4EFFFF 4F0000-4F7FFF 4F8000-4FFFFF 500000-507FFF 508000-50FFFF 510000-517FFF 518000-51FFFF 520000-527FFF 528000-52FFFF 530000-537FFF 538000-53FFFF 540000-547FFF 548000-54FFFF 550000-557FFF 558000-55FFFF 560000-567FFF 568000-56FFFF 570000-577FFF 578000-57FFFF 580000-587FFF 588000-58FFFF 590000-597FFF 598000-59FFFF 5A0000-5A7FFF 5A8000-5AFFFF 5B0000-5B7FFF 5B8000-5BFFFF 5C0000-5C7FFF 5C8000-5CFFFF 5D0000-5D7FFF 5D8000-5DFFFF 5E0000-5E7FFF 5E8000-5EFFFF 5F0000-5F7FFF 5F8000-5FFFFF 600000-607FFF 608000-60FFFF 610000-617FFF 618000-61FFFF
P/N:PM1170
REV. 0.04, JUL. 11, 2005
16
MX29LA128M T/B
Sector Group 58 58 58 58 59 59 59 59 60 60 60 60 61 61 61 61 62 62 62 62 63 63 63 63 64 64 64 64 65 65 65 65 66 66 66 66 67 67 67 67 Sector SA203 SA204 SA205 SA206 SA207 SA208 SA209 SA210 SA211 SA212 SA213 SA214 SA215 SA216 SA217 SA218 SA219 SA220 SA221 SA222 SA223 SA224 SA225 SA226 SA227 SA228 SA229 SA230 SA231 SA232 SA233 SA234 SA235 SA236 SA237 SA238 SA239 SA240 SA241 SA242 Sector Address A22-A12 11000100xxx 11000101xxx 11000110xxx 11000111xxx 11001000xxx 11001001xxx 11001010xxx 11001011xxx 11001100xxx 11001101xxx 11001110xxx 11001111xxx 11010000xxx 11010001xxx 11010010xxx 11010011xxx 11010100xxx 11010101xxx 11010110xxx 11010111xxx 11011000xxx 11011001xxx 11011010xxx 11011011xxx 11011100xxx 11011101xxx 11011110xxx 11011111xxx 11100000xxx 11100001xxx 11100010xxx 11100011xxx 11100100xxx 11100101xxx 11100110xxx 11100111xxx 11101000xxx 11101001xxx 11101010xxx 11101011xxx Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 (x8) Address Range C40000-4FFFFF C50000-5FFFFF C60000-6FFFFF C70000-7FFFFF C80000-8FFFFF C90000-9FFFFF CA0000-AFFFFF CB0000-BFFFFF CC0000-CFFFFF CD0000-DFFFFF CE0000-EFFFFF CF0000-FFFFFF D00000-0FFFFF D10000-1FFFFF D20000-2FFFFF D30000-3FFFFF D40000-4FFFFF D50000-5FFFFF D60000-6FFFFF D70000-7FFFFF D80000-8FFFFF D90000-9FFFFF DA0000-AFFFFF DB0000-BFFFFF DC0000-CFFFFF DD0000-DFFFFF DE0000-EFFFFF DF0000-FFFFFF E00000-0FFFFF E10000-1FFFFF E20000-2FFFFF E30000-3FFFFF E40000-4FFFFF E50000-5FFFFF E60000-6FFFFF E70000-7FFFFF E80000-8FFFFF E90000-9FFFFF EA0000-AFFFFF EB0000-BFFFFF (x16) Address Range 620000-627FFF 628000-62FFFF 630000-637FFF 638000-63FFFF 640000-647FFF 648000-64FFFF 650000-657FFF 658000-65FFFF 660000-667FFF 668000-66FFFF 670000-677FFF 678000-67FFFF 680000-687FFF 688000-68FFFF 690000-697FFF 698000-69FFFF 6A0000-6A7FFF 6A8000-6AFFFF 6B0000-6B7FFF 6B8000-6BFFFF 6C0000-6C7FFF 6C8000-6CFFFF 6D0000-6D7FFF 6D8000-6DFFFF 6E0000-6E7FFF 6E8000-6EFFFF 6F0000-6F7FFF 6F8000-6FFFFF 700000-707FFF 708000-70FFFF 710000-717FFF 718000-71FFFF 720000-727FFF 728000-72FFFF 730000-737FFF 738000-73FFFF 740000-747FFF 748000-74FFFF 750000-757FFF 758000-75FFFF
P/N:PM1170
REV. 0.04, JUL. 11, 2005
17
MX29LA128M T/B
Sector Group 68 68 68 68 69 69 69 69 70 70 70 70 71 71 71 71 72 72 72 72 Sector SA243 SA244 SA245 SA246 SA247 SA248 SA249 SA250 SA251 SA252 SA253 SA254 SA255 SA256 SA257 SA258 SA259 SA260 SA261 SA262 Sector Address A22-A12 11101100xxx 11101101xxx 11101110xxx 11101111xxx 11110000xxx 11110001xxx 11110010xxx 11110011xxx 11110100xxx 11110101xxx 11110110xxx 11110111xxx 11111000xxx 11111001xxx 11111010xxx 11111011xxx 11111100xxx 11111101xxx 11111110xxx 11111111xxx Sector Size (Kbytes/Kwords) 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 64/32 (x8) Address Range EC0000-CFFFFF ED0000-DFFFFF EE0000-EFFFFF EF0000-FFFFFF F00000-0FFFFFF F10000-1FFFFF F20000-2FFFFF F30000-3FFFFF F40000-4FFFFF F50000-5FFFFF F60000-6FFFFF F70000-7FFFFF F80000-8FFFFF F90000-9FFFFF FA0000-AFFFFF FB0000-BFFFFF FC0000-CFFFFF FD0000-DFFFFF FE0000-EFFFFF FF0000-FF1FFF (x16) Address Range 760000-767FFF 768000-76FFFF 770000-777FFF 778000-77FFFF 780000-787FFF 788000-78FFFF 790000-797FFF 798000-79FFFF 7A0000-7A7FFF 7A8000-7AFFFF 7B0000-7B7FFF 7B8000-7BFFFF 7C0000-7C7FFF 7C8000-7CFFFF 7D0000-7D7FFF 7D8000-7DFFFF 7E0000-7E7FFF 7E8000-7EFFFF 7F0000-7F7FFF 7F8000-7F8FFF
P/N:PM1170
REV. 0.04, JUL. 11, 2005
18
MX29LA128M T/B
Table 1. BUS OPERATION (1)
Q8~Q15 Operation CE# OE# WE# RESET# Read L L H H X X AIN DOUT WP# ACC Address Q0~Q7 Word Mode DOUT Byte Mode Q8-Q14= High Z Q15=A-1 Write (Program/Erase) L H L H (Note 3) X AIN (Note 4) (Note 4 Q8-Q14= High Z Q15=A-1 Accelerated Program L H L H (Note 3) VHH AIN (Note 4) (Note 4) Q8-Q14= High Z Q15=A-1 Standby VCC 0.3V Output Disable Reset Sector Group Protect (Note 2) L X L H X H H X L X X VCC 0.3V H L VID X X H X X X X X High-Z High-Z High-Z High-Z X High-Z High-Z X X H X High-Z High-Z High-Z
Sector Addresses, (Note 4) A6=L,A3=L, A2=L, A1=H,A0=L
Chip unprotect (Note 2)
L
H
L
VID
H
X
Sector Addresses, (Note 4) A6=H, A3=L, A2=L, A1=H, A0=L
X
X
Temporary Sector Group Unprotect
X
X
X
VID
H
X
AIN
(Note 4) (Note 4)
High-Z
Legend: L=Logic LOW=VIL, H=Logic High=VIH, VID=12.00.5V, VHH=12.00.5V, X=Don't Care, AIN=Address IN, DIN=Data IN, DOUT=Data OUT Notes: 1. Address are A21:A0 in word mode; A21:A-1 in byte mode. Sector addresses are A21:A15 in both modes. 2. The sector group protect and chip unprotect functions may also be implemented via programming equipment. See the "Sector Group Protection and Chip Unprotect" section. 3. If WP#=VIL, all the sectors remain protected. If WP#=VIH, all sectors protection depends on whether they were last protected or unprotect using the method described in "Sector/ Sector Block Protection and Unprotect". 4. DIN or DOUT as required by command sequence, Data# polling or sector protect algorithm (see Figure 15).
P/N:PM1170
REV. 0.04, JUL. 11, 2005
19
MX29LA128M T/B
Table 2. AUTOSELECT CODES (High Voltage Method)
A22 A14 Description CE# OE# WE# to to A9 A8 to A7 VID X L A6 A5 to A4 X A3 to A2 L L L L H X X VID X L X H H L L H H L H L H A1 A0 Q8 to Q15 Word Mode 00 22 22 22 Byte Mode X X X X C2h 7Eh 11h 00h (bottom boot) 01h (top boot) 01h (protected), L L H SA X VID X L X L H L X X 00h (unprotected) 98h (factory locked), L L H X X VID X L X L H H X X 18h (not factory locked) 88h (factory locked), L L H X X VID X L X L H H X X 08h (not factory locked) Q7 to Q0
A15 A10 Manufacturer ID
29LA128MT/B
L
L
H
X
X
Cycle 1 Cycle 2 Cycle 3
Sector Group Protection Verification Secured Silicon Sector Indicator Bit (Q7), WP# protects top two address sector Secured Silicon Sector Indicator Bit (Q7), WP# protects bottom two address sector
Legend: L = Logic Low = VIL, H = Logic High = VIH, SA = Sector Address, X = Don't care.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
20
MX29LA128M T/B
REQUIREMENTS FOR READING ARRAY DATA
To read array data from the outputs, the system must drive the CE# and OE# pins to VIL. CE# is the power control and selects the device. OE# is the output control and gates array data to the output pins. WE# should remain at VIH. The internal state machine is set for reading array data upon device power-up, or after a hardware reset. This ensures that no spurious alteration of the memory content occurs during the power transition. No command is necessary in this mode to obtain array data. Standard microprocessor read cycles that assert valid address on the device address inputs produce valid data on the device data outputs. The device remains enabled for read access until the command register contents are altered. consists of the address bits required to uniquely select a sector. The Writing specific address and data commands or sequences into the command register initiates device operations. Table 1 defines the valid register command sequences. Writing incorrect address and data values or writing them in the improper sequence resets the device to reading array data. Section has details on erasing a sector or the entire chip, or suspending/resuming the erase operation. After the system writes the Automatic Select command sequence, the device enters the Automatic Select mode. The system can then read Automatic Select codes from the internal register (which is separate from the memory array) on Q7-Q0. Standard read cycle timings apply in this mode. Refer to the Automatic Select Mode and Automatic Select Command Sequence section for more information. ICC2 in the DC Characteristics table represents the active current specification for the write mode. The "AC Characteristics" section contains timing specification table and timing diagrams for write operations.
PAGE MODE READ
The MX29LA128M T/B offers "fast page mode read" function. This mode provides faster read access speed for random locations within a page. The page size of the device is 4 words/8 bytes. The appropriate page is selected by the higher address bits A0~A1(Word Mode)/A1~A1(Byte Mode) This is an asynchronous operation; the microprocessor supplies the specific word location. The system performance could be enhanced by initiating 1 normal read and 3 fast page read (for word mode A0A1) or 7 fast page read (for byte mode A-1~A1). When CE# is deasserted and reasserted for a subsequent access, the access time is tACC or tCE. Fast page mode accesses are obtained by keeping the "read-page addresses" constant and changing the "intra-read page" addresses.
WRITE BUFFER
Write Buffer Programming allows the system to write a maximum of 16 words/32 bytes in one programming operation. This results in faster effective programming time than the standard programming algorithms. See "Write Buffer" for more information.
ACCELERATED PROGRAM OPERATION
The device offers accelerated program operations through the ACC function. This is one of two functions provided by the ACC pin. This function is primarily intended to allow faster manufacturing throughput at the factory. If the system asserts VHH on this pin, the device automatically enters the aforementioned Unlock Bypass mode, temporarily unprotects any protected sectors, and uses the higher voltage on the pin to reduce the time required for program operations. Removing VHH from the ACC pin must not be at VHH for operations other than accelerated programming, or device damage may result.
WRITING COMMANDS/COMMAND QUENCES
SE-
To program data to the device or erase sectors of memory, the system must drive WE# and CE# to VIL, and OE# to VIH. An erase operation can erase one sector, multiple sectors, or the entire device. Table indicates the address space that each sector occupies. A "sector address"
P/N:PM1170
REV. 0.04, JUL. 11, 2005
21
MX29LA128M T/B
STANDBY MODE
When using both pins of CE# and RESET#, the device enter CMOS Standby with both pins held at VCC 0.3V. If CE# and RESET# are held at VIH, but not within the range of VCC 0.3V, the device will still be in the standby mode, but the standby current will be larger. During Auto Algorithm operation, VCC active current (ICC2) is required even CE# = "H" until the operation is completed. The device can be read with standard access time (tCE) from either of these standby modes, before it is ready to read data. but not within VSS0.3V, the standby current will be greater. The RESET# pin may be tied to system reset circuitry. A system reset would that also reset the Flash memory, enabling the system to read the boot-up firmware from the Flash memory. If RESET# is asserted during a program or erase operation, the RY/BY# pin remains a "0" (busy) until the internal reset operation is complete, which requires a time of tREADY (during Embedded Algorithms). The system can thus monitor RY/BY# to determine whether the reset operation is complete. If RESET# is asserted when a program or erase operation is completed within a time of tREADY (not during Embedded Algorithms). The system can read data tRH after the RESET# pin returns to VIH. Refer to the AC Characteristics tables for RESET# parameters and to Figure 3 for the timing diagram.
AUTOMATIC SLEEP MODE
The automatic sleep mode minimizes Flash device energy consumption. The device automatically enables this mode when address remain stable for tACC+30ns. The automatic sleep mode is independent of the CE#, WE#, and OE# control signals. Standard address access timings provide new data when addresses are changed. While in sleep mode, output data is latched and always available to the system. ICC4 in the DC Characteristics table represents the automatic sleep mode current specification.
SECTOR GROUP PROTECT OPERATION
The MX29LA128M T/B features hardware sector group protection. This feature will disable both program and erase operations for these sector group protected. In this device, a sector group consists of four adjacent sectors which are protected or unprotected at the same time. To activate this mode, the programming equipment must force VID on address pin A9 and control pin OE#, (suggest VID = 12V) A6 = VIL and CE# = VIL. (see Table 2) Programming of the protection circuitry begins on the falling edge of the WE# pulse and is terminated on the rising edge. Please refer to sector group protect algorithm and waveform. MX29LA128M T/B also provides another method. Which requires VID on the RESET# only. This method can be implemented either in-system or via programming equipment. This method uses standard microprocessor bus cycle timing. To verify programming of the protection circuitry, the programming equipment must force VID on address pin A9 ( with CE# and OE# at VIL and WE# at VIH). When A1=1, it will produce a logical "1" code at device output Q0 for a protected sector. Otherwise the device will produce 00H for the unprotected sector. In this mode, the addresses, except for A1, are don't care. Address locations with A1 = VIL are reserved to read manufacturer and device codes. (Read Silicon ID)
OUTPUT DISABLE
With the OE# input at a logic high level (VIH), output from the devices are disabled. This will cause the output pins to be in a high impedance state.
RESET# OPERATION
The RESET# pin provides a hardware method of resetting the device to reading array data. When the RESET# pin is driven low for at least a period of tRP, the device immediately terminates any operation in progress, tristates all output pins, and ignores all read/write commands for the duration of the RESET# pulse. The device also resets the internal state machine to reading array data. The operation that was interrupted should be reinitiated once the device is ready to accept another command sequence, to ensure data integrity Current is reduced for the duration of the RESET# pulse. When RESET# is held at VSS0.3V, the device draws CMOS standby current (ICC4). If RESET# is held at VIL
P/N:PM1170
REV. 0.04, JUL. 11, 2005
22
MX29LA128M T/B
It is also possible to determine if the group is protected in the system by writing a Read Silicon ID command. Performing a read operation with A1=VIH, it will produce a logical "1" at Q0 for the protected sector. last protected or unprotect using the method described in "Sector/Sector Group Protection and Chip Unprotect". Note that the WP# pin must not be left floating or unconnected; inconsistent behavior of the device may result.
CHIP UNPROTECT OPERATION
The MX29LA128M T/B also features the chip unprotect mode, so that all sectors are unprotected after chip unprotect is completed to incorporate any changes in the code. It is recommended to protect all sectors before activating chip unprotect mode. To activate this mode, the programming equipment must force VID on control pin OE# and address pin A9. The CE# pins must be set at VIL. Pins A6 must be set to VIH. (see Table 2) Refer to chip unprotect algorithm and waveform for the chip unprotect algorithm. The unprotect mechanism begins on the falling edge of the WE# pulse and is terminated on the rising edge. MX29LA128M T/B also provides another method. Which requires VID on the RESET# only. This method can be implemented either in-system or via programming equipment. This method uses standard microprocessor bus cycle timing. It is also possible to determine if the chip is unprotect in the system by writing the Read Silicon ID command. Performing a read operation with A1=VIH, it will produce 00H at data outputs (Q0-Q7) for an unprotect sector. It is noted that all sectors are unprotected after the chip unprotect algorithm is completed.
TEMPORARY SECTOR GROUP UNPROTECT OPERATION
This feature allows temporary unprotect of previously protected sector to change data in-system. The Temporary Sector Unprotect mode is activated by setting the RESET# pin to VID(11.5V-12.5V). During this mode, formerly protected sectors can be programmed or erased as unprotect sector. Once VID is remove from the RESET# pin, all the previously protected sectors are protected again.
SILICON ID READ OPERATION
Flash memories are intended for use in applications where the local CPU alters memory contents. As such, manufacturer and device codes must be accessible while the device resides in the target system. PROM programmers typically access signature codes by raising A9 to a high voltage. However, multiplexing high voltage onto address lines is not generally desired system design practice. MX29LA128M T/B provides hardware method to access the silicon ID read operation. Which method requires VID on A9 pin, VIL on CE#, OE#, A6, and A1 pins. Which apply VIL on A0 pin, the device will output MXIC's manufacture code of which apply VIH on A0 pin, the device will output MX29LA128M T/B device code.
WRITE PROTECT (WP#)
The write protect function provides a hardware method to protect all sectors without using VID. If the system asserts VIL on the WP# pin, the device disables program and erase functions in all sectors independently of whether those sectors were protected or unprotect using the method described in Sector/Sector Group Protection and Chip Unprotect". If the system asserts VIH on the WP# pin, the device reverts to whether the sectors were last set to be protected or unprotect. That is, sector protection or unprotection for the sectors depends on whether they were
VERIFY SECTOR GROUP PROTECT STATUS OPERATION
MX29LA128M T/B provides hardware method for sector group protect status verify. Which method requires VID on A9 pin, VIH on WE# and A1 pins, VIL on CE#, OE#, A6, and A0 pins, and sector address on A16 to A21 pins. Which the identified sector is protected, the device will output 01H. Which the identified sector is not protect, the device will output 00H.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
23
MX29LA128M T/B
DATA PROTECTION
The MX29LA128M T/B is designed to offer protection against accidental erasure or programming caused by spurious system level signals that may exist during power transition. During power up the device automatically resets the state machine in the Read mode. In addition, with its control register architecture, alteration of the memory contents only occurs after successful completion of specific command sequences. The device also incorporates several features to prevent inadvertent write cycles resulting from VCC power-up and power-down transition or system noise. of main sectors is as normally. This mode of operation continues until the system issues the Exit Secured Silicon Sector command sequence, or until power is removed from the device. On power-up, or following a hardware reset, the device reverts to sending command to sector SA0. Secured Silicon Sector address range 000000h-000007h 000008h-00007Fh ESN Unavailable Determined by Customer ESN factory locked Customer lockable
SECURED SILICON SECTOR
The MX29LA128M T/B features a OTP memory region where the system may access through a command sequence to create a permanent part identification as so called Electronic Serial Number (ESN) in the device. Once this region is programmed, any further modification on the region is impossible. The secured silicon sector is a 128 words in length, and uses a Secured Silicon Sector Indicator Bit (Q7) to indicate whether or not the Secured Silicon Sector is locked when shipped from the factory. This bit is permanently set at the factory and cannot be changed, which prevent duplication of a factory locked part. This ensures the security of the ESN once the product is shipped to the field. The MX29LA128M T/B offers the device with Secured Silicon Sector either factory locked or customer lockable. The factory-locked version is always protected when shipped from the factory , and has the Secured Silicon Sector Indicator Bit permanently set to a "1". The customer-lockable version is shipped with the Secured Silicon Sector unprotected, allowing customers to utilize that sector in any form they prefer. The customer-lockable version has the secured sector Indicator Bit permanently set to a "0". Therefore, the Secured Silicon Sector Indicator Bit prevents customer, lockable device from being used to replace devices that are factory locked. The system access the Secured Silicon Sector through a command sequence (refer to "Enter Secured Silicon/ Exit Secured Silicon Sector command Sequence). After the system has written the Enter Secured Silicon Sector command sequence, it may read the Secured Silicon Sector by using the address normally occupied by the first sector SA0. Once entry the Secured Silicon Sector the operation of boot sectors is disabled but the operation
FACTORY LOCKED:Secured Silicon Sector Programmed and Protected At the Factory
In device with an ESN, the Secured Silicon Sector is protected when the device is shipped from the factory. The Secured Silicon Sector cannot be modified in any way. A factory locked device has an 8-word random ESN at address 000000h-000007h.
CUSTOMER LOCKABLE:Secured Silicon Sector NOT Programmed or Protected At the Factory
As an alternative to the factory-locked version, the device may be ordered such that the customer may program and protect the 128-word Secured Silicon Sector. Programming and protecting the Secured Silicon Sector must be used with caution since, once protected, there is no procedure available for unprotected the Secured Silicon Sector area and none of the bits in the Secured Silicon Sector memory space can be modified in any way. The Secured Silicon Sector area can be protected using one of the following procedures: Write the three-cycle Enter Secured Silicon Sector Region command sequence, and then follow the in-system sector protect algorithm as shown in Figure 15, except that RESET# may be at either VIH or VID. This allows insystem protection of the Secured Silicon Sector without raising any device pin to a high voltage. Note that method is only applicable to the Secured Silicon Sector.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
24
MX29LA128M T/B
Write the three-cycle Enter Secured Silicon Sector Region command sequence, and then alternate method of sector protection described in the :Sector Group Protection and Unprotect" section. Once the Secured Silicon Sector is programmed, locked and verified, the system must write the Exit Secured Silicon Sector Region command sequence to return to reading and writing the remainder of the array.
POWER SUPPLY DE COUPLING
In order to reduce power switching effect, each device should have a 0.1uF ceramic capacitor connected between its VCC and GND.
LOW VCC WRITE INHIBIT
When VCC is less than VLKO the device does not accept any write cycles. This protects data during VCC power-up and power-down. The command register and all internal program/erase circuits are disabled, and the device resets. Subsequent writes are ignored until VCC is greater than VLKO. The system must provide the proper signals to the control pins to prevent unintentional write when VCC is greater than VLKO.
WRITE PULSE "GLITCH" PROTECTION
Noise pulses of less than 5ns (typical) on CE# or WE# will not initiate a write cycle.
LOGICAL INHIBIT
Writing is inhibited by holding any one of OE# = VIL, CE# = VIH or WE# = VIH. To initiate a write cycle CE# and WE# must be a logical zero while OE# is a logical one.
POWER-UP SEQUENCE
The MX29LA128M T/B powers up in the Read only mode. In addition, the memory contents may only be altered after successful completion of the predefined command sequences.
POWER-UP WRITE INHIBIT
If WE#=CE#=VIL and OE#=VIH during power up, the device does not accept commands on the rising edge of WE#. The internal state machine is automatically reset to the read mode on power-up.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
25
MX29LA128M T/B
SOFTWARE COMMAND DEFINITIONS
Device operations are selected by writing specific address and data sequences into the command register. Writing incorrect address and data values or writing them in the improper sequence will reset the device to the read mode. Table 3 defines the valid register command sequences. Note that the Erase Suspend (B0H) and Erase Resume (30H) commands are valid only while the Sector Erase operation is in progress. Either of the two reset command sequences will reset the device (when applicable). All addresses are latched on the falling edge of WE# or CE#, whichever happens later. All data are latched on rising edge of WE# or CE#, whichever happens first.
TABLE 3. MX29LA128M T/B COMMAND DEFINITIONS
First Bus Command Read (Note 5) Reset (Note 6) Automatic Select (Note 7) Manufacturer ID Device ID (Note 8) Secured Sector Factory Protect (Note 9) Sector Group Protect Verify (Note 10) Enter Secured Silicon Sector Exit Secured Silicon Sector Program Write to Buffer (Note 11) Program Buffer to Flash Write to Buffer Abort Reset (Note 12) Chip Erase Sector Erase Word Byte Word Byte Word Byte Word Byte Word Byte Word Byte Word Byte Word Byte Word Byte Word Byte Word Byte Word Byte
Program/Erase Suspend (Note 13) Program/Erase Resume (Note 14)
Second Bus Third Bus Cycle Cycle
Fourth Bus Cycle Data
Fifth Bus Cycle
Sixth Bus Cycle
Bus 1 1 4 4 4 4 4 4 4 4 3 3 4 4 4 4 6 6 1 1 3 3 6 6 6 6 1 1 1 1
Cycle RA XXX 555 AAA 555 AAA 555 AAA 555 AAA 555 AAA 555 AAA 555 AAA 555 AAA SA SA 555 AAA 555 AAA 555 AAA XXX XXX 55 AA RD F0 AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA AA 29 29 AA AA AA AA AA AA B0 30 98 98
Cycles Addr Data Addr
Data Addr Data Addr
Addr Data Addr Data
2AA 555 2AA 555 2AA 555 2AA 555 2AA 555 2AA 555 2AA 555 2AA 555
55 55 55 55 55 55 55 55 55 55 55 55 55 55 55 55
555 555 555 555 555 555 555 SA SA
90 90 90 90 88 90 A0 25 25
X00 X00 X01 X02 X03 X06
C2H C2H ID1 ID1 see note 9 X0E ID2 X1C ID2 X0F ID3 X1E ID3
AAA 90 AAA 90 AAA 90 AAA 90 AAA 88
(SA)X02 XX00/ (SA)X04 XX01
XXX XXX PA PA SA SA
00 00 PD PD WC BC PA PA PD PD WBL PD WBL PD
AAA 90 AAA A0
2AA 555 2AA 555 2AA 555
55 55 55 55 55 55
555 555 555
F0 80 80 555 AAA 555 AAA AA AA AA AA 2AA 55 555 55 2AA 55 555 55 555 10 AAA 10 SA SA 30 30
AAA F0 AAA 80 AAA 80
CFI Query (Note 15)
Word Byte
P/N:PM1170
REV. 0.04, JUL. 11, 2005
26
MX29LA128M T/B
Legend: X=Don't care RA=Address of the memory location to be read. RD=Data read from location RA during read operation. PA=Address of the memory location to be programmed. Addresses are latched on the falling edge of the WE# or CE# pulse, whichever happen later. DDI=Data of device identifier C2H for manufacture code
PD=Data to be programmed at location PA. Data is latched on the rising edge of WE# or CE# pulse. SA=Address of the sector to be erase or verified (in autoselect mode). Address bits A21-A12 uniquely select any sector. WBL=Write Buffer Location. Address must be within the same write buffer page as PA. WC=Word Count. Number of write buffer locations to load minus 1. BC=Byte Count. Number of write buffer locations to load minus 1.
Notes: 1. See Table 1 for descriptions of bus operations. 2. All values are in hexadecimal. 3. Except when reading array or automatic select data, all bus cycles are write operation. 4. Address bits are don't care for unlock and command cycles, except when PA or SA is required. 5. No unlock or command cycles required when device is in read mode. 6. The Reset command is required to return to the read mode when the device is in the automatic select mode or if Q5 goes high. 7. The fourth cycle of the automatic select command sequence is a read cycle. 8. The device ID must be read in three cycles. The data is 01h for top boot and 00h for bottom boot. 9. If WP# protects the top two address sectors, the data is 98h for factory locked and 18h for not factory locked. If WP# protects the bottom two address sectors, the data is 88h for factory locked and 08h for not factor locked. 10. The data is 00h for an unprotected sector/sector block and 01h for a protected sector/sector block. 11. The total number of cycles in the command sequence is determined by the number of words written to the write buffer. The maximum number of cycles in the command sequence is 21(Word Mode) / 37(Byte Mode). 12. Command sequence resets device for next command after aborted write-to-buffer operation. 13. The system may read and program functions in non-erasing sectors, or enter the automatic select mode, when in the erase Suspend mode. The Erase Suspend command is valid only during a sector erase operation. 14. The Erase Resume command is valid only during the Erase Suspend mode. 15. Command is valid when device is ready to read array data or when device is in automatic select mode.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
27
MX29LA128M T/B
READING ARRAY DATA
The device is automatically set to reading array data after device power-up. No commands are required to retrieve data. The device is also ready to read array data after completing an Automatic Program or Automatic Erase algorithm. After the device accepts an Erase Suspend command, the device enters the Erase Suspend mode. The system can read array data using the standard read timings, except that if it reads at an address within erasesuspended sectors, the device outputs status data. After completing a programming operation in the Erase Suspend mode, the system may once again read array data with the same exception. See Erase Suspend/Erase Resume Commands for more information on this mode. The system must issue the reset command to re-enable the device for reading array data if Q5 goes high, or while in the automatic select mode. See the "Reset Command" section, next. array data (also applies during Erase Suspend).
SILICON ID READ COMMAND SEQUENCE
The SILICON ID READ command sequence allows the host system to access the manufacturer and devices codes, and determine whether or not a sector is protected. Table 2 shows the address and data requirements. This method is an alternative to that shown in Table 1, which is intended for PROM programmers and requires VID on address bit A9. The SILICON ID READ command sequence is initiated by writing two unlock cycles, followed by the SILICON ID READ command. The device then enters the SILICON ID READ mode, and the system may read at any address any number of times, without initiating another command sequence. A read cycle at address XX00h retrieves the manufacturer code. A read cycle at address XX01h returns the device code. A read cycle containing a sector address (SA) and the address 02h returns 01h if that sector is protected, or 00h if it is unprotected. Refer to Table for valid sector addresses. The system must write the reset command to exit the automatic select mode and return to reading array data.
RESET COMMAND
Writing the reset command to the device resets the device to reading array data. Address bits are don't care for this command. The reset command may be written between the sequence cycles in an erase command sequence before erasing begins. This resets the device to reading array data. Once erasure begins, however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in a program command sequence before programming begins. This resets the device to reading array data (also applies to programming in Erase Suspend mode). Once programming begins, however, the device ignores reset commands until the operation is complete. The reset command may be written between the sequence cycles in an SILICON ID READ command sequence. Once in the SILICON ID READ mode, the reset command must be written to return to reading array data (also applies to SILICON ID READ during Erase Suspend). If Q5 goes high during a program or erase operation, writing the reset command returns the device to reading
BYTE/WORD PROGRAM COMMAND SEQUENCE
The command sequence requires four bus cycles, and is initiated by writing two unlock write cycles, followed by the program set-up command. The program address and data are written next, which in turn initiate the Embedded Program algorithm. The system is not required to provide further controls or timings. The device automatically generates the program pulses and verifies the programmed cell margin. Table 3 shows the address and data requirements for the byte program command sequence. When the Embedded Program algorithm is complete, the device then returns to reading array data and addresses are no longer latched. The system can determine the status of the program operation by using Q7, Q6, or RY/ BY#. See "Write Operation Status" for information on these status bits. Any commands written to the device during the Embedded Program Algorithm are ignored. Note that a hardREV. 0.04, JUL. 11, 2005
P/N:PM1170
28
MX29LA128M T/B
ware reset immediately terminates the programming operation. The Byte/Word Program command sequence should be reinitiated once the device has reset to reading array data, to ensure data integrity. Programming is allowed in any sequence and across sector boundaries. A bit cannot be programmed from a "0" back to a "1". Attempting to do so may halt the operation and set Q5 to "1", or cause the Data# Polling algorithm to indicate the operation was successful. However, a succeeding read will show that the data is still "0". Only erase operations can convert a "0" to a "1". multiple times, the address/data pair counter will be decremented for every data load operation. The host system must therefore account for loading a write-buffer location more than once. The counter decrements for each data load operation, not for each unique write-buffer-address location. Note also that if an address location is loaded more than once into the buffer, the final data loaded for that address will be programmed. Once the specified number of write buffer locations have been loaded, the system must then write the Program Buffer to Flash command at the sector address. Any other address and data combination aborts the Write Buffer Programming operation. The device then begins programming. Data polling should be used while monitoring the last address location loaded into the write buffer. Q7, Q6, Q5, and Q1 should be monitored to determine the device status during Write Buffer Programming. The write-buffer programming operation can be suspended using the standard program suspend/resume commands. Upon successful completion of the Write Buffer Programming operation, the device is ready to execute the next command. The Write Buffer Programming Sequence can be aborted in the following ways: * Load a value that is greater than the page buffer size during the Number of Locations to Program step. * Write to an address in a sector different than the one specified during the Write-Buffer-Load command. * Write an Address/Data pair to a different write-bufferpage than the one selected by the Starting Address during the write buffer data loading stage of the operation. * Write data other than the Confirm Command after the specified number of data load cycles. The abort condition is indicated by Q1 = 1, Q7 = DATA# (for the last address location loaded), Q6 = toggle, and Q5=0. A Write-to-Buffer-Abort Reset command sequence must be written to reset the device for the next operation. Note that the full 3-cycle Write-to-Buffer-Abort Reset command sequence is required when using WriteBuffer-Programming features in Unlock Bypass mode.
Write Buffer Programming
Write Buffer Programming allows the system write to a maximum of 16 words/32 bytes in one programming operation. This results in faster effective programming time than the standard programming algorithms. The Write Buffer Programming command sequence is initiated by first writing two unlock cycles. This is followed by a third write cycle containing the Write Buffer Load command written at the Sector Address in which programming will occur. The fourth cycle writes the sector address and the number of word locations, minus one, to be programmed. For example, if the system will program 6 unique address locations, then 05h should be written to the device. This tells the device how many write buffer addresses will be loaded with data and therefore when to expect the Program Buffer to Flash command. The number of locations to program cannot exceed the size of the write buffer or the operation will abort. The fifth cycle writes the first address location and data to be programmed. The write-buffer-page is selected by address bits AMAX-4. All subsequent address/data pairs must fall within the selected-write-buffer-page. The system then writes the remaining address/data pairs into the write buffer. Write buffer locations may be loaded in any order. The write-buffer-page address must be the same for all address/data pairs loaded into the write buffer. (This means Write Buffer Programming cannot be performed across multiple write-buffer pages. This also means that Write Buffer Programming cannot be performed across multiple sectors. If the system attempts to load programming data outside of the selected write-buffer page, the operation will abort. Note that if a Write Buffer address location is loaded
Program Suspend/Program Resume Command Sequence
The Program Suspend command allows the system to interrupt a programming operation or a Write to Buffer
P/N:PM1170
REV. 0.04, JUL. 11, 2005
29
MX29LA128M T/B
programming operation so that data can be read from any non-suspended sector. When the Program Suspend command is written during a programming process, the device halts the program operation within 15us maximum (5 us typical) and updates the status bits. Addresses are not required when writing the Program Suspend command. After the programming operation has been suspended, the system can read array data from any non-suspended sector. The Program Suspend command may also be issued during a programming operation while an erase is suspended. In this case, data may be read from any addresses not in Erase Suspend or Program Suspend. If a read is needed from the Secured Silicon Sector area (One-time Program area), then user must use the proper command sequences to enter and exit this region. The system may also write the autoselect command sequence when the device is in the Program Suspend mode. The system can read as many autoselect codes as required. When the device exits the autoselect mode, the device reverts to the Program Suspend mode, and is ready for another valid operation. See Autoselect Command Sequence for more information. After the Program Resume command is written, the device reverts to programming. The system can determine the status of the program operation using the Q7 or Q6 status bits, just as in the standard program operation. See Write Operation Status for more information.
AUTOMATIC CHIP/SECTOR ERASE COMMAND
The device does not require the system to preprogram prior to erase. The Automatic Erase algorithm automatically pre-program and verifies the entire memory for an all zero data pattern prior to electrical erase. The system is not required to provide any controls or timings during these operations. Table 3 shows the address and data requirements for the chip erase command sequence. Any commands written to the chip during the Automatic Erase algorithm are ignored. Note that a hardware reset during the chip erase operation immediately terminates the operation. The Chip Erase command sequence should be reinitiated once the device has returned to reading array data, to ensure data integrity. The system can determine the status of the erase operation by using Q7, Q6, Q2, or RY/BY#. See "Write Operation Status" for information on these status bits. When the Automatic Erase algorithm is complete, the device returns to reading array data and addresses are no longer latched. Figure 10 illustrates the algorithm for the erase operation. See the Erase/Program Operations tables in "AC Characteristics" for parameters, and to Figure 9 for timing diagrams.
SETUP AUTOMATIC CHIP/SECTOR ERASE
Chip erase is a six-bus cycle operation. There are two "unlock" write cycles. These are followed by writing the "set-up" command 80H. Two more "unlock" write cycles are then followed by the chip erase command 10H, or the sector erase command 30H. The MX29LA128M T/B contains a Silicon-ID-Read operation to supplement traditional PROM programming methodology. The operation is initiated by writing the read silicon ID command sequence into the command register. Following the command write, a read cycle with A1=VIL,A0=VIL retrieves the manufacturer code. A read cycle with A1=VIL, A0=VIH returns the device code.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
30
MX29LA128M T/B
SECTOR ERASE COMMANDS
The Automatic Sector Erase does not require the device to be entirely pre-programmed prior to executing the Automatic Set-up Sector Erase command and Automatic Sector Erase command. Upon executing the Automatic Sector Erase command, the device will automatically program and verify the sector(s) memory for an all-zero data pattern. The system is not required to provide any control or timing during these operations. When the sector(s) is automatically verified to contain an all-zero pattern, a self-timed sector erase and verify begin. The erase and verify operations are complete when the data on Q7 is "1" and the data on Q6 stops toggling for two consecutive read cycles, at which time the device returns to the Read mode. The system is not required to provide any control or timing during these operations. When using the Automatic Sector Erase algorithm, note that the erase automatically terminates when adequate erase margin has been achieved for the memory array (no erase verification command is required). Sector erase is a six-bus cycle operation. There are two "unlock" write cycles. These are followed by writing the set-up command 80H. Two more "unlock" write cycles are then followed by the sector erase command 30H. The sector address is latched on the falling edge of WE# or CE#, whichever happens later , while the command (data) is latched on the rising edge of WE# or CE#, whichever happens first. Sector addresses selected are loaded into internal register on the sixth falling edge of WE# or CE#, whichever happens later. Each successive sector load cycle started by the falling edge of WE# or CE#, whichever happens later must begin within 50us from the rising edge of the preceding WE# or CE#, whichever happens first. Otherwise, the loading period ends and internal auto sector erase cycle starts. (Monitor Q3 to determine if the sector erase timer window is still open, see section Q3, Sector Erase Timer.) Any command other than Sector Erase(30H) or Erase Suspend(B0H) during the time-out period resets the device to read mode. device requires a maximum 20us to suspend the sector erase operation. However, When the Erase Suspend command is written during the sector erase time-out, the device immediately terminates the time-out period and suspends the erase operation. After this command has been executed, the command register will initiate erase suspend mode. The state machine will return to read mode automatically after suspend is ready. At this time, state machine only allows the command register to respond to the Erase Resume, program data to, or read data from any sector not selected for erasure. The system can determine the status of the program operation using the Q7 or Q6 status bits, just as in the standard program operation. After an erase-suspend program operation is complete, the system can once again read array data within non-suspended blocks.
ERASE RESUME
This command will cause the command register to clear the suspend state and return back to Sector Erase mode but only if an Erase Suspend command was previously issued. Erase Resume will not have any effect in all other conditions. Another Erase Suspend command can be written after the chip has resumed erasing.
ERASE SUSPEND
This command only has meaning while the state machine is executing Automatic Sector Erase operation, and therefore will only be responded during Automatic Sector Erase operation. When the Erase Suspend command is issued during the sector erase operation, the
P/N:PM1170
REV. 0.04, JUL. 11, 2005
31
MX29LA128M T/B
QUERY COMMAND AND COMMON FLASH INTERFACE (CFI) MODE
MX29LA128M T/B is capable of operating in the CFI mode. This mode all the host system to determine the manufacturer of the device such as operating parameters and configuration. Two commands are required in CFI mode. Query command of CFI mode is placed first, then the Reset command exits CFI mode. These are described in Table 4. The single cycle Query command is valid only when the device is in the Read mode, including Erase Suspend, Standby mode, and Read ID mode; however, it is ignored otherwise. The Reset command exits from the CFI mode to the Read mode, or Erase Suspend mode, or read ID mode. The command is valid only when the device is in the CFI mode.
Table 4-1. CFI mode: Identification Data Values
(All values in these tables are in hexadecimal) Description Query-unique ASCII string "QRY" Address h Address h (x16) (x8) 10 20 11 22 12 24 13 26 14 28 15 2A 16 2C 17 2E 18 30 19 32 1A 34 Data h 0051 0052 0059 0002 0000 0040 0000 0000 0000 0000 0000
Primary vendor command set and control interface ID code Address for primary algorithm extended query table Alternate vendor command set and control interface ID code (none) Address for secondary algorithm extended query table (none)
Table 4-2. CFI Mode: System Interface Data Values
Description VCC supply, minimum (2.7V) VCC supply, maximum (3.6V) VPP supply, minimum (none) VPP supply, maximum (none) Typical timeout for single word/byte write (2N us) Typical timeout for maximum size buffer write (2N us) Typical timeout for individual block erase (2N ms) Typical timeout for full chip erase (2N ms) Maximum timeout for single word/byte write times (2N X Typ) Maximum timeout for maximum size buffer write times (2N X Typ) Maximum timeout for individual block erase times (2N X Typ) Maximum timeout for full chip erase times (not supported)
P/N:PM1170
Address h Address h (x16) (x8) 1B 36 1C 38 1D 3A 1E 3C 1F 3E 20 40 21 42 22 44 23 46 24 48 25 4A 26 4C
Data h 0027 0036 0000 0000 0007 0007 000A 0000 0001 0005 0004 0000
REV. 0.04, JUL. 11, 2005
32
MX29LA128M T/B
Table 4-3. CFI Mode: Device Geometry Data Values
Description Device size (2n bytes) Flash device interface code Address h Address h (x16) (x8) 27 4E 28 50 29 52 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 54 56 58 5A 5C 5E 60 62 64 66 68 6A 6C 6E 70 72 74 76 78 Data h 0018 0002 0000 0005 0000 0002 0007 0000 0020 0000 00FE 0000 0000 0001 0000 0000 0000 0000 0000 0000 0000 0000
Maximum number of bytes in multi-byte write =2N Number of erase block regions (X=# of Erase Block Regions) Erase block region 1 information [2E,2D] = # of blocks in region -1 [30, 2F] = size in multiples of 256-bytes
Erase Block Region 2 Information (refer to CFI publication 100)
Erase Block Region 3 Information (refer to CFI publication 100)
Erase Block Region 4 Information (refer to CFI publication 100)
P/N:PM1170
REV. 0.04, JUL. 11, 2005
33
MX29LA128M T/B
Table 4-4. CFI Mode: Primary Vendor-Specific Extended Query Data Values
Description Query-unique ASCII string "PRI" Address h Address h (x16) 40 41 42 Major version number, ASCII Minor version number, ASCII Address sensitive unlock (0=required, 1= not required) Erase suspend (2= to read and write) Sector protect (N= # of sectors/group) Temporary sector unprotect (1=supported) Sector protect/unprotect scheme Simultaneous R/W operation (0=not supported) Burst mode type (0=not supported) Page mode type (1=4 word page) ACC (Acceleration) Supply Minimum 00h=Not Supported, D7-D4: Volt, D3-D0:100mV ACC (Acceleration) Supply Maximum 00h=Not Supported, D7-D4: Volt, D3-D0:100mV Top/Bottom Boot Sector Flag 02h=Bottom Boot Device, 03h=Top Boot Device 04h=uniform sectors bottom WP# protect, 05h=uniform sectors top WP# protect Program Suspend 00h=Not Supported, 01h=Supported 50 A0 0001 4F 9E 0002/ 0003 4E 9C 00C5 43 44 45 46 47 48 49 4A 4B 4C 4D (x8) 80 82 84 86 88 8A 8C 8E 90 92 94 96 98 9A 0050 0052 0049 0031 0033 0000 0002 0001 0001 0004 0000 0000 0001 00B5 Data h
P/N:PM1170
REV. 0.04, JUL. 11, 2005
34
MX29LA128M T/B
WRITE OPERATION STATUS
The device provides several bits to determine the status of a write operation: Q2, Q3, Q5, Q6, Q7, and RY/BY#. Table 5 and the following subsections describe the functions of these bits. Q7, RY/BY#, and Q6 each offer a method for determining whether a program or erase operation is complete or in progress. These three bits are discussed first.
Table 5. Write Operation Status
Status Byte/Word Program in Auto Program Algorithm Auto Erase Algorithm Erase Suspend Read Erase Suspended Mode (Erase Suspended Sector) Erase Suspend Read (Non-Erase Suspended Sector) Erase Suspend Program Program-Suspended Read Program Suspend Write-to-Buffer (Program-Suspended Sector) Program-Suspended Read (Non-Program-Suspended Sector) Busy Abort Q7# Q7# Toggle Toggle 0 0 N/A N/A N/A N/A 0 1 0 0 Data 1 Q7# Toggle 0 N/A N/A N/A 0 1 Invalid (not allowed) Data Q7 Q7# 0 1 Q6 Toggle Toggle No Toggle Data Data Data Data Data 1 Q5 0 0 0 Q3 N/A 1 N/A Q2 No Toggle Toggle Toggle N/A N/A 0 1 Q1 0 RY/BY# 0
Notes: 1. Q5 switches to "1" when an Word/Byte Program, Erase, or Write-to-Buffer operation has exceeded the maximum timing limits. Refer to the section on Q5 for more information. 2. Q7 and Q2 require a valid address when reading status information. Refer to the appropriate subsection for further details. 3. The Data# Polling algorithm should be used to monitor the last loaded write-buffer address location. 4. Q1 switches to "1" when the device has aborted the write-to-buffer operation.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
35
MX29LA128M T/B
Q7: Data# Polling
The Data# Polling bit, Q7, indicates to the host system whether an Automatic Algorithm is in progress or completed, or whether the device is in Erase Suspend. Data# Polling is valid after the rising edge of the final WE# pulse in the program or erase command sequence. During the Automatic Program algorithm, the device outputs on Q7 the complement of the datum programmed to Q7. This Q7 status also applies to programming during Erase Suspend. When the Automatic Program algorithm is complete, the device outputs the datum programmed to Q7. The system must provide the program address to read valid status information on Q7. If a program address falls within a protected sector, Data# Polling on Q7 is active for approximately 1 us, then the device returns to reading array data. During the Automatic Erase algorithm, Data# Polling produces a "0" on Q7. When the Automatic Erase algorithm is complete, or if the device enters the Erase Suspend mode, Data# Polling produces a "1" on Q7. This is analogous to the complement/true datum output described for the Automatic Program algorithm: the erase function changes all the bits in a sector to "1" prior to this, the device outputs the "complement," or "0". The system must provide an address within any of the sectors selected for erasure to read valid status information on Q7. After an erase command sequence is written, if all sectors selected for erasing are protected, Data# Polling on Q7 is active for approximately 100 us, then the device returns to reading array data. If not all selected sectors are protected, the Automatic Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. When the system detects Q7 has changed from the complement to true data, it can read valid data at Q7-Q0 on the following read cycles. This is because Q7 may change asynchronously with Q0-Q6 while Output Enable (OE#) is asserted low. happens first pulse in the command sequence (prior to the program or erase operation), and during the sector time-out. During an Automatic Program or Erase algorithm operation, successive read cycles to any address cause Q6 to toggle. The system may use either OE# or CE# to control the read cycles. When the operation is complete, Q6 stops toggling. After an erase command sequence is written, if all sectors selected for erasing are protected, Q6 toggles for 100us and returns to reading array data. If not all selected sectors are protected, the Automatic Erase algorithm erases the unprotected sectors, and ignores the selected sectors that are protected. The system can use Q6 and Q2 together to determine whether a sector is actively erasing or is erase suspended. When the device is actively erasing (that is, the Automatic Erase algorithm is in progress), Q6 toggling. When the device enters the Erase Suspend mode, Q6 stops toggling. However, the system must also use Q2 to determine which sectors are erasing or erase-suspended. Alternatively, the system can use Q7. If a program address falls within a protected sector, Q6 toggles for approximately 2us after the program command sequence is written, then returns to reading array data. Q6 also toggles during the erase-suspend-program mode, and stops toggling once the Automatic Program algorithm is complete. Table 5 shows the outputs for Toggle Bit I on Q6.
Q2:Toggle Bit II
The "Toggle Bit II" on Q2, when used with Q6, indicates whether a particular sector is actively erasing (that is, the Automatic Erase algorithm is in process), or whether that sector is erase-suspended. Toggle Bit II is valid after the rising edge of the final WE# or CE#, whichever happens first pulse in the command sequence. Q2 toggles when the system reads at addresses within those sectors that have been selected for erasure. (The system may use either OE# or CE# to control the read cycles.) But Q2 cannot distinguish whether the sector is actively erasing or is erase-suspended. Q6, by com-
Q6:Toggle BIT I
Toggle Bit I on Q6 indicates whether an Automatic Program or Erase algorithm is in progress or complete, or whether the device has entered the Erase Suspend mode. Toggle Bit I may be read at any address, and is valid after the rising edge of the final WE# or CE#, whichever
P/N:PM1170
REV. 0.04, JUL. 11, 2005
36
MX29LA128M T/B
parison, indicates whether the device is actively erasing, or is in Erase Suspend, but cannot distinguish which sectors are selected for erasure. Thus, both status bits are required for sectors and mode information. Refer to Table 5 to compare outputs for Q2 and Q6. If this time-out condition occurs during sector erase operation, it specifies that a particular sector is bad and it may not be reused. However, other sectors are still functional and may be used for the program or erase operation. The device must be reset to use other sectors. Write the Reset command sequence to the device, and then execute program or erase command sequence. This allows the system to continue to use the other active sectors in the device. If this time-out condition occurs during the chip erase operation, it specifies that the entire chip is bad or combination of sectors are bad. If this time-out condition occurs during the byte/word programming operation, it specifies that the entire sector containing that byte is bad and this sector may not be reused, (other sectors are still functional and can be reused). The time-out condition may also appear if a user tries to program a non blank location without erasing. In this case the device locks out and never completes the Automatic Algorithm operation. Hence, the system never reads a valid data on Q7 bit and Q6 never stops toggling. Once the Device has exceeded timing limits, the Q5 bit will indicate a "1". Please note that this is not a device failure condition since the device was incorrectly used. The Q5 failure condition may appear if the system tries to program a to a "1" location that is previously programmed to "0". Only an erase operation can change a "0" back to a "1". Under this condition, the device halts the operation, and when the operation has exceeded the timing limits, Q5 produces a "1".
Reading Toggle Bits Q6/ Q2
Whenever the system initially begins reading toggle bit status, it must read Q7-Q0 at least twice in a row to determine whether a toggle bit is toggling. Typically, the system would note and store the value of the toggle bit after the first read. After the second read, the system would compare the new value of the toggle bit with the first. If the toggle bit is not toggling, the device has completed the program or erase operation. The system can read array data on Q7-Q0 on the following read cycle. However, if after the initial two read cycles, the system determines that the toggle bit is still toggling, the system also should note whether the value of Q5 is high (see the section on Q5). If it is, the system should then determine again whether the toggle bit is toggling, since the toggle bit may have stopped toggling just as Q5 went high. If the toggle bit is no longer toggling, the device has successfully completed the program or erase operation. If it is still toggling, the device did not complete the operation successfully, and the system must write the reset command to return to reading array data. The remaining scenario is that system initially determines that the toggle bit is toggling and Q5 has not gone high. The system may continue to monitor the toggle bit and Q5 through successive read cycles, determining the status as described in the previous paragraph. Alternatively, it may choose to perform other system tasks. In this case, the system must start at the beginning of the algorithm when it returns to determine the status of the operation.
Q3:Sector Erase Timer
After the completion of the initial sector erase command sequence, the sector erase time-out will begin. Q3 will remain low until the time-out is complete. Data# Polling and Toggle Bit are valid after the initial sector erase command sequence. If Data# Polling or the Toggle Bit indicates the device has been written with a valid erase command, Q3 may be used to determine if the sector erase timer window is still open. If Q3 is high ("1") the internally controlled erase cycle has begun; attempts to write subsequent commands to the device will be ignored until the erase operation is completed as indicated by Data# Polling or
Q5:Program/Erase Timing
Q5 will indicate if the program or erase time has exceeded the specified limits (internal pulse count). Under these conditions Q5 will produce a "1". This time-out condition indicates that the program or erase cycle was not successfully completed. Data# Polling and Toggle Bit are the only operating functions of the device under this condition.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
37
MX29LA128M T/B
Toggle Bit. If Q3 is low ("0"), the device will accept additional sector erase commands. To insure the command has been accepted, the system software should check the status of Q3 prior to and following each subsequent sector erase command. If Q3 were high on the second status check, the command may not have been accepted. If the time between additional erase commands from the system can be less than 50us, the system need not to monitor Q3.
Q1: Write-to-Buffer Abort
Q1 indicates whether a Write-to-Buffer operation was aborted. Under these conditions Q1 produces a "1". The system must issue the Write-to-Buffer-Abort-Reset command sequence to return the device to reading array data. See Write Buffer section for more details.
RY/BY#:READY/BUSY OUTPUT
The RY/BY# is a dedicated, open-drain output pin that indicates whether an Embedded Algorithm is in progress or complete. The RY/BY# status is valid after the rising edge of the final WE# pulse in the command sequence. Since RY/BY# is an open-drain output, several RY/BY# pins can be tied together in parallel with a pull-up resistor to VCC . If the output is low (Busy), the device is actively erasing or programming. (This includes programming in the Erase Suspend mode.) If the output is high (Ready), the device is ready to read array data (including during the Erase Suspend mode), or is in the standby mode.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
38
MX29LA128M T/B
ABSOLUTE MAXIMUM RATINGS
Storage Temperature Plastic Packages . . . . . . . . . . . . . ..... -65oC to +150oC Ambient Temperature with Power Applied. . . . . . . . . . . . . .... -65oC to +125oC Voltage with Respect to Ground VCC (Note 1) . . . . . . . . . . . . . . . . . -0.5 V to +4.0 V A9, OE#, and RESET# (Note 2) . . . . . . . . . . . ....-0.5 V to +12.5 V All other pins (Note 1) . . . . . . . -0.5 V to VCC +0.5 V Output Short Circuit Current (Note 3) . . . . . . 200 mA Notes: 1. Minimum DC voltage on input or I/O pins is -0.5 V. During voltage transitions, input or I/O pins may overshoot VSS to -2.0 V for periods of up to 20 ns. Maximum DC voltage on input or I/O pins is VCC +0.5 V. During voltage transitions, input or I/O pins may overshoot to VCC +2.0 V for periods up to 20ns. 2. Minimum DC input voltage on pins A9, OE#, and RESET# is -0.5 V. During voltage transitions, A9, OE#, and RESET# may overshoot VSS to -2.0 V for periods of up to 20 ns. Maximum DC input voltage on pin A9 is +12.5 V which may overshoot to 14.0 V for periods up to 20 ns. 3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second. Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability.
OPERATING RATINGS
Commercial (C) Devices Ambient Temperature (TA ). . . . . . . . . . . . 0 C to +70 C Industrial (I) Devices Ambient Temperature (TA ). . . . . . . . . . -40 C to +85 C VCC Supply Voltages VCC for full voltage range. . . . . . . . . . . +2.7 V to 3.6 V
Operating ranges define those limits between which the functionality of the device is guaranteed.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
39
MX29LA128M T/B
TA=-40 C to 85 C, VCC=2.7V~3.6V (VCC=3.0V~3.6V for 90R)
Test Conditions VIN = VSS to VCC , VCC = VCC max VCC=VCC max; A9 = 12.5V VOUT = VSS to VCC , VCC = VCC max CE# = VIL, 10 MHz OE# = VIH 5 MHz 1 MHz CE# = VIL , 10 MHz OE# = VIH 40 MHz CE# = VIL , OE# = VIH CE#, RESET# = VCC 0.3V WP# = VIH RESET# = VSS 0.3V WP# = VIH VIL = VSS 0.3 V, VIH = VCC 0.3 V, WP# = VIH -0.5 0.7xVCC 11.5 11.5 Min. Typ. Max. 1.0 35 1.0 35 18 5 5 10 50 20 20 20 50 25 20 20 40 60 50 50 50 Unit uA uA uA mA mA mA mA mA mA uA uA uA
DC CHARACTERISTICS
Parameter Description I LI Input Load Current (Note 1) I LIT I LO A9 Input Leakage Current Output Leakage Current
ICC1 VCC Initial Read Current (Notes 2,3) ICC2 VCC Intra-Page Read Current (Notes 2,3) ICC3 VCC Active Write Current (Notes 2,4,6) ICC4 VCC Standby Current (Note 2) ICC5 VCC Reset Current (Note 2) ICC6 Automatic Sleep Mode (Notes 2,5) VIL VIH VHH Input Low Voltage Input High Voltage Voltage for ACC Program Acceleration VID Voltage for Autoselect and Temporary Sector Unprotect VOL Output Low Voltage VOH1 Output High Voltage VOH2 VLKO Low VCC Lock-Out Voltage (Note 4)
VCC = 2.7V ~ 3.6V VCC = 3.0 V 10%
12.0 12.0
0.8 VCC+0.5 12.5 12.5 0.45
V V V V V V V V
IOL= 4.0mA,VCC=VCC min IOH=-2.0mA,VCC=VCC min 0.85VCC IOH=-100uA,VCC=VCC min VCC-0.4 2.3
2.5
Notes: 1. On the WP#/ACC pin only, the maximum input load current when WP# = VIL is 5.0uA. 2. Maximum ICC specifications are tested with VCC = VCC max. 3. The ICC current listed is typically is less than 2 mA/MHz, with OE# at VIH. Typical specifications are for VCC = 3.0V. 4. ICC active while Embedded Erase or Embedded Program is in progress. 5. Automatic sleep mode enables the low power mode when addresses remain stable for t ACC + 30 ns. 6. Not 100% tested. 7. A9=12.5V when TA=0 C to 85 C, A9=12V when when TA=-40 C to 0 C.
P/N:PM1170 REV. 0.04, JUL. 11, 2005
40
MX29LA128M T/B
SWITCHING TEST CIRCUITS TEST SPECIFICATIONS
Test Condition Output Load Output Load Capacitance, CL (including jig capacitance) Input Rise and Fall Times Input Pulse Levels Input timing measurement reference levels Output timing measurement reference levels All Speeds 1 TTL gate 30 5 0.0-3.0 1.5 1.5 Unit pF ns V V V
DEVICE UNDER TEST
2.7K ohm 3.3V
CL
6.2K ohm
DIODES=IN3064 OR EQUIVALENT
KEY TO SWITCHING WAVEFORMS
WAVEFORM INPUTS Steady Changing from H to L Changing from L to H Don't Care, Any Change Permitted Does Not Apply Changing, State Unknown Center Line is High Impedance State(High Z) OUTPUTS
SWITCHING TEST WAVEFORMS
3.0V
1.5V
Measurement Level
1.5V OUTPUT
0.0V INPUT
P/N:PM1170
REV. 0.04, JUL. 11, 2005
41
MX29LA128M T/B
AC CHARACTERISTICS Read-Only Operations
Parameter Std. tRC tACC tCE tPACC tOE tDF tDF tOH Description Read Cycle Time (Note 1) Address to Output Delay Chip Enable to Output Delay Page Access Time Output Enable to Output Delay Chip Enable to Output High Z (Note 1) Output Enable to Output High Z (Note 1) Output Hold Time From Address, CE# or OE#, whichever Occurs First Read tOEH Output Enable Hold Time (Note 1) Toggle and Data# Polling Min Min 35 10 ns ns CE#, OE#=VIL OE#=VIL Test Setup Min Max Max Max Max Max Max Min
TA=-40 C to 85 C, VCC=2.7V~3.6V (VCC=3.0V~3.6V for 90R)
Speed Options 90R 90 90 90 25 35 16 16 0 100 100 100 100 25 35 Unit ns ns ns ns ns ns ns ns
Notes: 1. Not 100% tested. 2. See SWITCHING TEST CIRCUITS and TEST SPECIFICATIONS TABLE for test specifications.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
42
MX29LA128M T/B
Figure 1. READ TIMING WAVEFORMS
tRC VIH
Addresses
VIL
ADD Valid
tCE VIH
CE#
VIL tRH tRH VIH
WE#
VIL VIH VIL tOH tOEH tOE tDF
OE#
tACC
Outputs
VOH VOL VIH
HIGH Z
DATA Valid
HIGH Z
RESET#
VIL
RY/BY#
0V
Figure 2. PAGE READ TIMING WAVEFORMS
A2-A21
Same Page
(A-1), A0~A2
tACC
CE#
tPACC
OE#
tPACC
tPACC
Output
Qa
Qb
Qc
Qd
P/N:PM1170
REV. 0.04, JUL. 11, 2005
43
MX29LA128M T/B
AC CHARACTERISTICS
Parameter tREADY1 tREADY2 tRP tRH tRB tRPD Description RESET# PIN Low (During Automatic Algorithms) to Read or Write (See Note) RESET# PIN Low (NOT During Automatic Algorithms) to Read or Write (See Note) RESET# Pulse Width (NOT During Automatic Algorithms) RESET# High Time Before Read (See Note) RY/BY# Recovery Time(to CE#, OE# go low) RESET# Low to Standby Mode MIN MIN MIN MIN 500 50 0 20 ns ns ns us MAX 500 ns Test Setup All Speed Options Unit MAX 20 us
Note:Not 100% tested
Figure 3. RESET# TIMING WAVEFORM
RY/BY#
CE#, OE#
tRH
RESET#
tRP tReady2
Reset Timing NOT during Automatic Algorithms
tReady1
RY/BY#
tRB
CE#, OE#
RESET#
tRP
Reset Timing during Automatic Algorithms
P/N:PM1170
REV. 0.04, JUL. 11, 2005
44
MX29LA128M T/B
AC CHARACTERISTICS Erase and Program Operations
Parameter Std. tWC tAS tASO tAH tAHT tDS tDH tCEPH tOEPH tGHWL tGHEL tCS tCH tWP tWPH
TA=-40 C to 85 C, VCC=2.7V~3.6V (VCC=3.0V~3.6V for 90R)
Speed Options 90R 100 90 100 0 15 45 0 35 0 20 20 0 0 0 0 35 30 240 60 60 54 54 0.5 50 0 90 250 4 100 Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns us us us us us sec us ns ns ns us
tWHWH1
tWHWH2 tVCS tRB tBUSY tVHH tPOLL
Description Write Cycle Time (Note 1) Address Setup Time Address Setup Time to OE# low during toggle bit polling Address Hold Time Address Hold Time From CE# or OE# high during toggle bit polling Data Setup Time Data Hold Time CE# High During Toggle Bit Polling Output Enable High during toggle bit polling Read Recovery Time Before Write (OE# High to WE# Low) Read Recovery Time Before Write CE# Setup Time CE# Hold Time Write Pulse Width Write Pulse Width High Write Buffer Program Operation (Notes 2,3) Single Word/Byte Program Byte Operation (Notes 2,5) Word Accelerated Single Word/Byte Byte Programming Operation (Notes 2,5) Word Sector Erase Operation (Note 2) VCC Setup Time (Note 1) Write Recovery Time from RY/BY# Program/Erase Valid to RY/BY# Delay VHH Rise and Fall Time (Note 1) Program Valid Before Status Polling (Note 6)
Min Min Min Min Min Min Min Min Min Min Min Min Min Min Min Typ Typ Typ Typ Typ Typ Min Min Min Min Max
Notes: 1. Not 100% tested. 2. See the "Erase And Programming Performance" section for more information. 3. For 1-16 words/1-32 bytes programmed. 4. Effective write buffer specification is based upon a 16-word/32-byte write buffer operation. 5. Word/Byte programming specification is based upon a single word/byte programming operation not utilizing the write buffer. 6. When using the program suspend/resume feature, if the suspend command is issued within tPOLL, tPOLL must be fully re-applied upon resuming the programming operation. If the suspend command is issued after tPOLL, tPOLL is not required again prior to reading the status bits upon resuming.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
45
MX29LA128M T/B
ERASE/PROGRAM OPERATION Figure 4. AUTOMATIC PROGRAM TIMING WAVEFORMS
Program Command Sequence(last two cycle)
tWC tAS
Read Status Data (last two cycle)
Address
XXXh
PA
tAH
PA
PA
CE#
tCH
OE#
tWP
tWHWH1
WE#
tCS tDS tDH
tWPH
A0h Data
PD
Status
DOUT
tBUSY
tRB
RY/BY#
tVCS
VCC
Note : 1.PA=Program Address, PD=Program Data, DOUT is the true data the program address
Figure 5. ACCELERATED PROGRAM TIMING DIAGRAM
VHH
ACC
VIL or VIH VIL or VIH
tVHH
tVHH
P/N:PM1170
REV. 0.04, JUL. 11, 2005
46
MX29LA128M T/B
Figure 6. AUTOMATIC PROGRAMMING ALGORITHM FLOWCHART
START
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data A0H Address 555H
Write Program Data/Address
Increment Address
Data Poll from system
No Verify Word Ok ?
YES
No Last Address ?
YES
Auto Program Completed
P/N:PM1170
REV. 0.04, JUL. 11, 2005
47
MX29LA128M T/B
Figure 7. WRITE BUFFER PROGRAMMING ALGORITHM FLOWCHART
Write "Write to Buffer" command and Sector Address
Write number of addresses to program minus 1(WC) and Sector Address
Part of "Write to Buffer" Command Sequence
Write first address/data
Yes WC = 0 ?
No Yes Write to a different sector address
Abort Write to Buffer Operation ? No (Note 1) Write next address/data pair
Write to buffer ABORTED. Must write "Write-to-buffer Abort Reset" command sequence to return to read mode.
WC = WC - 1
Write program buffer to flash sector address
Read Q7~Q0 at Last Loaded Address
Yes Q7 = Data ? No
No No
Q1 = 1 ?
Q5 = 1 ?
Yes Yes Read Q7~Q0 with address = Last Loaded Address
Notes: 1. When Sector Address is specified, any address in the selected sector is acceptable. However, when loading Write-Buffer address locations with data, all addresses must fall within the selected Write-Buffer Page. 2. Q7 may change simultaneously with Q5. Therefore, Q7 should be verified. 3. If this flowchart location was reached because Q5= "1" then the device FAILED. If this flowchart location was reached because Q1="1", then the Write to Buffer operation was ABORTED. In either case, the proper reset command must be written before the device can begin another operation. If Q1=1, write the Write-Buffer-Programming-Abort-Reset command. If Q5=1, write the Reset command. 4. See Table 3 for command sequences required for write buffer programming.
(Note 2)
Q7 and Q15 = Data ?
Yes
No (Note 3) FAIL or ABORT PASS
P/N:PM1170
REV. 0.04, JUL. 11, 2005
48
MX29LA128M T/B
Figure 8. PROGRAM SUSPEND/RESUME FLOWCHART
Program Operation or Write-to-Buffer Sequence in Progress Write Program Suspend Command Sequence Command is also valid for Erase-suspended-program operations
Write address/data XXXh/B0h
Wait 15us
Read data as required
Autoselect and Secured Sector read operations are also allowed Data cannot be read from erase-or program-suspended sectors
No Done reading ? Yes Write address/data XXXh/30h Write Program Resume Command Sequence
Device reverts to operation prior to Program Suspend
P/N:PM1170
REV. 0.04, JUL. 11, 2005
49
MX29LA128M T/B
Figure 9. AUTOMATIC CHIP/SECTOR ERASE TIMING WAVEFORM
Erase Command Sequence(last two cycle)
tWC tAS
Read Status Data
Address
2AAh
SA
555h for chip erase tAH
VA
VA
CE#
tCH
OE#
tWP
tWHWH2
WE#
tCS tDS tDH
tWPH
55h Data
30h
10 for Chip Erase
In Progress Complete
tBUSY
tRB
RY/BY#
tVCS
VCC
Note : 1.SA=sector address(for Sector Erase), VA=Valid Address for reading status data(see "Write Operation Status").
P/N:PM1170
REV. 0.04, JUL. 11, 2005
50
MX29LA128M T/B
Figure 10. AUTOMATIC CHIP ERASE ALGORITHM FLOWCHART
START
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 80H Address 555H
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 10H Address 555H
Data Poll from system YES
No
DATA = FFh ?
YES
Auto Erase Completed
P/N:PM1170
REV. 0.04, JUL. 11, 2005
51
MX29LA128M T/B
Figure 11. AUTOMATIC SECTOR ERASE ALGORITHM FLOWCHART
START
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 80H Address 555H
Write Data AAH Address 555H
Write Data 55H Address 2AAH
Write Data 30H Sector Address
Last Sector to Erase ?
NO
YES Data Poll from System
NO Data=FFh? YES
Auto Sector Erase Completed
P/N:PM1170
REV. 0.04, JUL. 11, 2005
52
MX29LA128M T/B
Figure 12. ERASE SUSPEND/RESUME FLOWCHART
START
Write Data B0H
NO Toggle Bit checking Q6 not toggled YES Read Array or Program
ERASE SUSPEND
Reading or Programming End YES Write Data 30H
NO
ERASE RESUME Continue Erase
Another Erase Suspend ? YES
NO
P/N:PM1170
REV. 0.04, JUL. 11, 2005
53
MX29LA128M T/B
AC CHARACTERISTICS Alternate CE# Controlled Erase and Program Operations TA=-40 C to 85 C, VCC=2.7V~3.6V (VCC=3.0V~3.6V for 90R)
Parameter Std. tWC tAS tAH tDS tDH tGHEL tWS tWH tCP tCPH Description Write Cycle Time (Note 1) Address Setup Time Address Hold Time Data Setup Time Data Hold Time Read Recovery Time Before Write (OE# High to WE# Low) WE# Setup Time WE# Hold Time CE# Pulse Width CE# Pulse Width High Write Buffer Program Operation (Notes 2,3) Single Word/Byte Program tWHWH1 Operation (Notes 2,5) Accelerated Single Word/Byte Programming Operation (Notes 2,5) tWHWH2 tRH tPOLL Sector Erase Operation (Note 2) RESET HIGH Time Before Write (Note 1) Program Valid Before Status Polling (Note 6) Byte Word Byte Word Min Min Min Min Typ Typ Typ Typ Typ Typ Min Max 0 0 35 25 240 60 60 54 54 0.5 50 4 ns ns ns ns us us us us us sec ns us Min Min Min Min Min Min Speed Options 90R 90 0 45 35 0 0 100 100 Unit ns ns ns ns ns ns
Notes: 1. Not 100% tested. 2. See the "Erase And Programming Performance" section for more information. 3. For 1-16 words/1-32 bytes programmed. 4. Effective write buffer specification is based upon a 16-word/32-byte write buffer operation. 5. Word/Byte programming specification is based upon a single word/byte programming operation not utilizing the write buffer. 6. When using the program suspend/resume feature, if the suspend command is issued within tPOLL, tPOLL must be fully re-applied upon resuming the programming operation. If the suspend command is issued after tPOLL, tPOLL is not required again prior to reading the status bits upon resuming.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
54
MX29LA128M T/B
Figure 13. CE# CONTROLLED PROGRAM TIMING WAVEFORM
555 for program 2AA for erase PA for program SA for sector erase 555 for chip erase
Data# Polling Address
tWC tWH tAS tAH
PA
WE#
tGHEL
OE#
tCP tWHWH1 or 2
CE#
tWS tDS tDH
tCPH tBUSY
Q7 Data
tRH A0 for program 55 for erase PD for program 30 for sector erase 10 for chip erase
DOUT
RESET#
RY/BY#
NOTES: 1.PA=Program Address, PD=Program Data, DOUT=Data Out, Q7=complement of data written to device. 2.Figure indicates the last two bus cycles of the command sequence.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
55
MX29LA128M T/B
SECTOR GROUP PROTECT/CHIP UNPROTECT Figure 14. Sector Group Protect / Chip Unprotect Waveform (RESET# Control)
VID VIH
RESET#
SA, A6 A1, A0
Valid*
Valid*
Valid*
Sector Group Protect or Chip Unprotect Data
1us
Verify 40h Status
60h
60h
Sector Group Protect:150us Chip Unprotect:15ms
CE#
WE#
OE#
Note: For sector group protect A6=0, A1=1, A0=0. For chip unprotect A6=1, A1=1, A0=0
P/N:PM1170
REV. 0.04, JUL. 11, 2005
56
MX29LA128M T/B
Figure 15. IN-SYSTEM SECTOR GROUP PROTECT/CHIP UNPROTECT ALGORITHMS WITH RESET#=VID
START START PLSCNT=1 Protect all sectors: The indicated portion of the sector protect algorithm must be performed for all unprotected sectors prior to issuing the first sector unprotect address
PLSCNT=1
RESET#=VID
RESET#=VID
Wait 1us
Wait 1us
Temporary Sector Unprotect Mode
No
First Write Cycle=60h? Yes Set up sector address No Sector Protect: Write 60h to sector address with A6=0, A1=1, A0=0
First Write Cycle=60h? Yes
No
Temporary Sector Unprotect Mode
All sectors protected? Yes Set up first sector address
Wait 150us
Verify Sector Protect: Write 40h to sector address with A6=0, A1=1, A0=0 Increment PLSCNT Read from sector address with A6=0, A1=1, A0=0 No
Reset PLSCNT=1
Sector Unprotect: Write 60h to sector address with A6=1, A1=1, A0=0
Wait 15 ms
Increment PLSCNT No PLSCNT=25? Data=01h?
Verify Sector Unprotect: Write 40h to sector address with A6=1, A1=1, A0=0 Read from sector address with A6=1, A1=1, A0=0
Yes Device failed
Yes No Protect another sector? Yes No PLSCNT=1000?
Reset PLSCNT=1 Data=00h?
Sector Protect Algorithm
No Remove VID from RESET# Yes Device failed Write reset command Last sector verified? No Yes
Sector Protect complete
Chip Unprotect Algorithm
Yes Remove VID from RESET#
Write reset command
Sector Unprotect complete
P/N:PM1170
REV. 0.04, JUL. 11, 2005
57
MX29LA128M T/B
AC CHARACTERISTICS
Parameter tVLHT tWPP1 tOESP Description Voltage transition time Write pulse width for sector group protect OE# setup time to WE# active Test Setup Min. Min. Min. All Speed Options 4 100 4 Unit us ns us
Figure 16. SECTOR GROUP PROTECT TIMING WAVEFORM (A9, OE# Control)
A1
A6
12V 3V A9
tVLHT Verify
12V 3V OE#
tVLHT tWPP 1 tVLHT
WE#
tOESP
CE#
Data
tOE
01H
F0H
A21-A16
Sector Address
P/N:PM1170
REV. 0.04, JUL. 11, 2005
58
MX29LA128M T/B
Figure 17. SECTOR GROUP PROTECTION ALGORITHM (A9, OE# Control)
START
Set Up Sector Addr
PLSCNT=1
OE#=VID, A9=VID, CE#=VIL A6=VIL
Activate WE# Pulse
Time Out 150us
Set WE#=VIH, CE#=OE#=VIL A9 should remain VID
.
No
Read from Sector Addr=SA, A1=1
PLSCNT=32?
No
Data=01H?
Yes Device Failed
Protect Another Sector?
Yes
Remove VID from A9 Write Reset Command
Sector Protection Complete
P/N:PM1170
REV. 0.04, JUL. 11, 2005
59
MX29LA128M T/B
Figure 18. CHIP UNPROTECT TIMING WAVEFORM (A9, OE# Control)
A1
12V 3V A9
tVLHT
A6
Verify
12V 3V OE#
tVLHT tWPP 2 tVLHT
WE#
tOESP
CE#
Data
tOE
00H
F0H
P/N:PM1170
REV. 0.04, JUL. 11, 2005
60
MX29LA128M T/B
Figure 19. CHIP UNPROTECT FLOWCHART (A9, OE# Control)
START
Protect All Sectors
PLSCNT=1
Set OE#=A9=VID CE#=VIL, A6=1
Activate WE# Pulse
Time Out 15ms
Increment PLSCNT
Set OE#=CE#=VIL A9=VID, A1=1
Set Up First Sector Addr
Read Data from Device No
Increment Sector Addr
Data=00H?
No
PLSCNT=1000?
Yes No
Yes Device Failed
All sectors have been verified? Yes Remove VID from A9 Write Reset Command
Chip Unprotect Complete
* It is recommended before unprotect whole chip, all sectors should be protected in advance.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
61
MX29LA128M T/B
AC CHARACTERISTICS
Parameter tVIDR tRSP tRRB Description VID Rise and Fall Time (see Note) RESET# Setup Time for Temporary Sector Unprotect RESET# Hold Time from RY/BY# High for Temporary Sector Group Unprotect Test Setup Min Min Min 500 4 4 ns us us All Speed Options Unit
Figure 20. TEMPORARY SECTOR GROUP UNPROTECT WAVEFORMS
12V
RESET#
0 or 3V VIL or VIH
tVIDR
tVIDR
Program or Erase Command Sequence
CE#
WE#
tRSP tRRB
RY/BY#
P/N:PM1170
REV. 0.04, JUL. 11, 2005
62
MX29LA128M T/B
Figure 21. TEMPORARY SECTOR GROUP UNPROTECT FLOWCHART
Start
RESET# = VID (Note 1) Perform Erase or Program Operation Operation Completed RESET# = VIH Temporary Sector Unprotect Completed(Note 2)
Notes : 1. All protected sectors are temporary unprotected. VID=11.5V~12.5V 2. All previously protected sectors are protected again.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
63
MX29LA128M T/B
Figure 22. SECURED SILICON SECTOR PROTECTED ALGORITHMS FLOWCHART
START
Enter Secured Silicon Sector
Wait 1us
First Wait Cycle Data=60h
Second Wait Cycle Data=60h A6=0, A1=1, A0=0
Wait 300us
No
Data = 01h ?
Yes
Device Failed Write Reset Command
Secured Sector Protect Complete
P/N:PM1170
REV. 0.04, JUL. 11, 2005
64
MX29LA128M T/B
Figure 23. SILICON ID READ TIMING WAVEFORM
VCC
3V VID VIH VIL
VIH VIL tACC VIH VIL tACC tACC tACC
ADD A9
ADD A0
A1
A2
VIH VIL
ADD
VIH VIL
CE#
VIH VIL tCE
WE#
VIH VIL
OE#
VIH VIL
tOE tDF tOH tOH tOH tOH
VIH
DATA Q0-Q15
VIL
DATA OUT Manufacturer ID
DATA OUT Device ID Cycle 1
DATA OUT Device ID Cycle 2
DATA OUT Device ID Cycle 3
P/N:PM1170
REV. 0.04, JUL. 11, 2005
65
MX29LA128M T/B
WRITE OPERATION STATUS Figure 24. DATA# POLLING TIMING WAVEFORMS (DURING AUTOMATIC ALGORITHMS)
tRC
Address
VA
tACC tCE
VA
VA
CE#
tCH tOE
OE#
tOEH tDF
WE#
tOH
Q7 Q0-Q6
tBUSY
Status Data
Complement
True
Valid Data
High Z
Status Data
Status Data
True
Valid Data
High Z
RY/BY#
Note : VA=Valid address. Figure shows are first status cycle after command sequence, last status read cycle, and array data raed cycle.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
66
MX29LA128M T/B
Figure 25. DATA# POLLING ALGORITHM
Start
Read Q7~Q0 Add.=VA(1)
Q7 = Data ?
Yes
No No
Q5 = 1 ?
Yes Read Q7~Q0 Add.=VA
Q7 = Data ? (2) No FAIL
Yes
Pass
Notes: 1.VA=valid address for programming. 2.Q7 should be rechecked even Q5="1" because Q7 may change simultaneously with Q5.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
67
MX29LA128M T/B
Figure 26. TOGGLE BIT TIMING WAVEFORMS (DURING AUTOMATIC ALGORITHMS)
tRC
Address
VA
tACC tCE
VA
VA
VA
CE#
tCH tOE
OE#
tOEH tDF
WE#
tDH tOH
Q6/Q2
Valid Status
Valid Status (first read)
Valid Status (second read)
Valid Data (stops toggling)
Valid Data
RY/BY#
Note : VA=Valid address; not required for Q6. Figure shows first two status cycle after command sequence, last status read cycle, and array data read cycle.
P/N:PM1170
REV. 0.04, JUL. 11, 2005
68
MX29LA128M T/B
Figure 27. TOGGLE BIT ALGORITHM
START
Read Q7~Q0
Read Q7~Q0
(Note 1)
Toggle Bit Q6 =Toggle? YES
NO
NO Q5=1?
YES Read Q7~Q0 Twice (Note 1,2)
Toggle Bit Q6= Toggle? YES Program/Erase Operation Not Complete, Write Reset Command
Program/Erase Operation Complete
Notes : 1. Read toggle bit twice to determine whether or not it is toggling. 2. Recheck toggle bit because it may stop toggling as Q5 changes to "1".
P/N:PM1170
REV. 0.04, JUL. 11, 2005
69
MX29LA128M T/B
Figure 28. Q6 versus Q2
Enter Embedded Erasing
Erase Suspend Erase Erase Suspend Read
Enter Erase Suspend Program Erase Suspend Program Erase Suspend Read
Erase Resume Erase Erase Complete
WE#
Q6
Q2
Note : The system can use OE# or CE# to toggle Q2/Q6, Q2 toggles only when read at an address within an erase-suspended
P/N:PM1170
REV. 0.04, JUL. 11, 2005
70
MX29LA128M T/B
ERASE AND PROGRAMMING PERFORMANCE (1)
PARAMETER Sector Erase Time Typ (Note 1) 0.5 Max (Note 2) 2 Unit sec Comments Excludes 00h programming Chip Erase Time 128 256 sec prior to erasure Note 6 Total Write Buffer Program Time (Note 4) Total Accelerated Effective Write Buffer Program Time (Note 4) Chip Program Time 126 sec 240 200 us us Excludes system level overhead Note 7
Notes: 1. Typical program and erase times assume the following conditions: 25 C, 3.0V VCC. Programming specifications assume checkboard data pattern. 2. Maximum values are measured at VCC = 3.0 V, worst case temperature. Maximum values are valid up to and including 100,000 program/erase cycles. 3. Word/Byte programming specification is based upon a single word/byte programming operation not utilizing the write buffer. 4. For 1-16 words or 1-32 bytes programmed in a single write buffer programming operation. 5. Effective write buffer specification is calculated on a per-word/per-byte basis for a 16-word/32-byte write buffer operation. 6. In the pre-programming step of the Embedded Erase algorithm, all bits are programmed to 00h before erasure. 7. System-level overhead is the time required to execute the command sequence(s) for the program command. See Tables 3 for further information on command definitions. 8. The device has a minimum erase and program cycle endurance of 100,000 cycles.
LATCH-UP CHARACTERISTICS
MIN. Input Voltage with respect to GND on all pins except I/O pins Input Voltage with respect to GND on all I/O pins Current Includes all pins except VCC. Test conditions: VCC = 3.0V, one pin at a time. -1.0V -1.0V -100mA MAX. 13.5V VCC + 1.0V +100mA
DATA RETENTION
Parameter Minimum Pattern Data Retention Time Min 20 Unit Years
P/N:PM1170
REV. 0.04, JUL. 11, 2005
71
MX29LA128M T/B
TSOP PIN AND BGA PACKAGE CAPACITANCE
Parameter Symbol CIN COUT CIN2 Parameter Description Input Capacitance Output Capacitance Control Pin Capacitance Test Set VIN=0 VOUT=0 VIN=0 TSOP CSP TSOP CSP TSOP CSP Notes: 1. Sampled, not 100% tested. 2. Test conditions TA=25 C, f=1.0MHz TYP 6 4.2 8.5 5.4 7.5 3.9 MAX 7.5 5.0 12 6.5 9 4.7 UNIT pF pF pF pF pF pF
P/N:PM1170
REV. 0.04, JUL. 11, 2005
72
MX29LA128M T/B
ORDERING INFORMATION
PLASTIC PACKAGE PART NO. MX29LA128MTTC-90R MX29LA128MTTC-10 MX29LA128MBTC-90R MX29LA128MBTC-10 MX29LA128MTTI-90R MX29LA128MTTI-10 MX29LA128MBTI-90R MX29LA128MBTI-10 ACCESS TIME (ns) 90 100 90 100 90 100 90 100 PACKAGE 56 Pin TSOP (Normal Type) 56 Pin TSOP (Normal Type) 56 Pin TSOP (Normal Type) 56 Pin TSOP (Normal Type) 56 Pin TSOP (Normal Type) 56 Pin TSOP (Normal Type) 56 Pin TSOP (Normal Type) 56 Pin TSOP (Normal Type) Remark
P/N:PM1170
REV. 0.04, JUL. 11, 2005
73
MX29LA128M T/B
PACKAGE INFORMATION
P/N:PM1170
REV. 0.04, JUL. 11, 2005
74
MX29LA128M T/B
REVISION HISTORY
Revision No. Description 0.01 1. Revised 90 ns as 90R ns, and added 100 ns option 2. Removed PB free order information 1. Changed standby current from 1uA to 20uA 1. To modify WP# protect function 1. Changed title from "Advanced Information" to "Preliminary" 2. To add note 7 for ILIT parameter in DC Characteristics table 3. To add comments into performance table Page P1,40,42, P45,54 P73 P1 P1,19,23 P1 P40 P71 Date DEC/29/2004
0.02 0.03 0.04
APR/21/2005 JUN/10/2005 JUL/11/2005
P/N:PM1170
REV. 0.04, JUL. 11, 2005
75
MX29LA128M T/B
MACRONIX INTERNATIONAL CO., LTD.
Headquarters:
TEL:+886-3-578-6688 FAX:+886-3-563-2888
Europe Office :
TEL:+32-2-456-8020 FAX:+32-2-456-8021
Hong Kong Office :
TEL:+86-755-834-335-79 FAX:+86-755-834-380-78
Japan Office :
Kawasaki Office :
TEL:+81-44-246-9100 FAX:+81-44-246-9105
Osaka Office :
TEL:+81-6-4807-5460 FAX:+81-6-4807-5461
Singapore Office :
TEL:+65-6346-5505 FAX:+65-6348-8096
Taipei Office :
TEL:+886-2-2509-3300 FAX:+886-2-2509-2200
MACRONIX AMERICA, INC.
TEL:+1-408-262-8887 FAX:+1-408-262-8810
http : //www.macronix.com
MACRONIX INTERNATIONAL CO., LTD. reserves the right to change product and specifications without notice.


▲Up To Search▲   

 
Price & Availability of MX29LA128MTTI-90R

All Rights Reserved © IC-ON-LINE 2003 - 2022  

[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy]
Mirror Sites :  [www.datasheet.hk]   [www.maxim4u.com]  [www.ic-on-line.cn] [www.ic-on-line.com] [www.ic-on-line.net] [www.alldatasheet.com.cn] [www.gdcy.com]  [www.gdcy.net]


 . . . . .
  We use cookies to deliver the best possible web experience and assist with our advertising efforts. By continuing to use this site, you consent to the use of cookies. For more information on cookies, please take a look at our Privacy Policy. X